Whereas, pursuant to section 19a of the Hazardous Products Actb, the Minister of Health has consulted with the government of each province and with the organizations representative of workers, organizations representative of employers and organizations representative of suppliers that the Minister considers appropriate;Therefore, His Excellency the Governor General in Council, on the recommendation of the Minister of Health, pursuant to subsection 15(1)c of the Hazardous Products Actb, makes the annexed Hazardous Products Regulations.S.C. 2014, c. 20, s. 120R.S., c. H-3S.C. 2014, c. 20, ss. 115(1) to (3)InterpretationDefinitionsThe following definitions apply in these Regulations.Act means the Hazardous Products Act. (Loi)aerosol dispenser means a non-refillable receptacle made of metal, glass or plastic and containing a gas that is compressed, liquefied or dissolved under pressure, with or without a liquid, foam, mousse, paste, gel or powder, and fitted with a release device allowing the contents to be ejected in the form of solid or liquid particles in suspension in a gas, as a foam, mousse, paste, gel or powder or in a liquid or gaseous state. (générateur d’aérosol)ATE means an acute toxicity estimate, and includes the LD50 and the LC50, and the acute toxicity point estimate determined in accordance with the table to section 8.1.7. (ETA)CAS registry number means the identification number assigned to a chemical by the Chemical Abstracts Service, a division of the American Chemical Society. (numéro d’enregistrement CAS)chemical name means a scientific designation of a material or substance that is made in accordance with the rules of nomenclature of either the Chemical Abstracts Service, a division of the American Chemical Society, or the International Union of Pure and Applied Chemistry, or a scientific designation of a material or substance that is internationally recognized and that clearly identifies the material or substance. (dénomination chimique)flash point means the lowest temperature, corrected to the standard pressure of 101.3 kPa, at which the application of an ignition source causes the vapours of a liquid to ignite. (point d’éclair)gas means a mixture or substance thatat 50°C has an absolute vapour pressure of greater than 300 kPa; oris completely gaseous at 20°C and at the standard pressure of 101.3 kPa. (gaz)GHS means the United Nations document entitled Globally Harmonized System of Classification and Labelling of Chemicals (GHS), Seventh Revised Edition. (SGH)hazardous ingredient means an ingredient in a mixture that, when evaluated as an individual substance, is classified in a category or subcategory of a health hazard class. (ingrédient dangereux)hazard statement means a phrase assigned to a category or subcategory of a hazard class or, in the case of column 5 of Parts 4 to 6 of Schedule 5, the required statement that describes the nature of the hazard presented by a hazardous product. (mention de danger)initial boiling point means the temperature of a liquid at which its vapour pressure is equal to the standard pressure of 101.3 kPa, i.e., the temperature at which the first gas bubble appears. (point d’ébullition initial)initial supplier identifier means the name, address and telephone number ofthe manufacturer; orthe importer of the hazardous product who operates in Canada. (identificateur du fournisseur initial)LC50 means the concentration of a mixture or substance in air that causes the death of 50.0% of a group of test animals. (CL50)LD50 means the single dose of a mixture or substance that, when administered by a particular exposure route in an animal study, is expected to cause the death of 50.0% of a given animal population. (DL50)liquid means a mixture or substance thatat 50°C has a vapour pressure of 300 kPa or less;is not completely gaseous at 20°C and at the standard pressure of 101.3 kPa; andhas a melting point or initial melting point of 20°C or less at the standard pressure of 101.3 kPa or, in the case of a mixture or substance for which neither can be determined, is shownto be a liquid as a result of the ASTM International method ASTM D4359-90, entitled Standard Test Method for Determining Whether a Material Is a Liquid or a Solid, as amended from time to time, orto not be pasty as a result of the test for determining fluidity (penetrometer test), referred to in section 4 of chapter 3 of Part 2, numbered 2.3.4, of Annex A of the European Agreement Concerning the International Carriage of Dangerous Goods by Road, as amended from time to time. (liquide)Manual of Tests and Criteria means the United Nations document entitled Manual of Tests and Criteria, as amended from time to time. (Manuel d’épreuves et de critères)manufacturer means a supplier who, in the course of business in Canada, manufactures, produces, processes, packages or labels a hazardous product and sells it. (fabricant)OECD means the Organisation for Economic Co-operation and Development. (OCDE)outer container means the most outward container of a hazardous product that is visible under normal conditions of handling, but does not include the most outward container if it is the only container of the hazardous product. (contenant externe)pictogram means a graphical composition that includes a symbol along with other graphical elements, such as a border or background colour. (pictogramme)precautionary statement means a phrase that describes the recommended measures to take in order to minimize or prevent adverse effects resulting from exposure to a hazardous product or resulting from improper storage or handling of a hazardous product. (conseil de prudence)product identifier means, in respect of a hazardous product, the brand name, chemical name, common name, generic name or trade name. (identificateur de produit)risk group classification means, in relation to the “Biohazardous Infectious Materials” health hazard class, classification in Risk Group 2, Risk Group 3 or Risk Group 4 as defined in subsection 3(1) of the Human Pathogens and Toxins Act. (classification par groupe de risque)SADT or self-accelerating decomposition temperature means the lowest temperature at which self-accelerating decomposition occurs. (TDAA ou température de décomposition autoaccélérée)scientifically validated method means, in relation to a hazard, a method that specifies standards for the evaluation of that hazard and whose results are accurate and reproducible, in accordance with established scientific principles. (méthode validée sur le plan scientifique)signal word means, in respect of a hazardous product, the word “Danger” or “Warning” that is used to alert the reader to a potential hazard and to indicate its severity. (mention d’avertissement)solid means a mixture or substance that is not a liquid or gas. (solide)United Nations Model Regulations means the United Nations document entitled Recommendations on the Transport of Dangerous Goods: Model Regulations, as amended from time to time. (Règlement type des Nations Unies)UN number means the four-digit identification number issued in accordance with the United Nations Model Regulations. (numéro ONU)vapour means the gaseous form of a mixture or substance released from its liquid or solid state. (vapeur)work place means a place where a person works for remuneration. (lieu de travail)Reference to hazard classIn these Regulations, a reference to a hazard class is to be read as a reference to a hazard class that is listed in Schedule 2 to the Act.Health professionalsFor the purposes of Parts 5 and 6, health professionals arephysicians who are registered, and entitled under the laws of a province to practise medicine and who are practising medicine under those laws in that province; andnurses who are registered or licensed, and entitled under the laws of a province to practise nursing and who are practising nursing under those laws in that province.Interpretation of “should”When the word “should” is used in a text that is referenced or incorporated by reference in these Regulations, it is to be read as imperative, unless the context requires otherwise.SOR/2022-272, s. 1Classification of a Product, Mixture, Material or SubstanceGeneralOrder of decreasing severityIn each Subpart of Parts 7 and 8, the categories and subcategories in each of the classification tables to those Subparts are set out in the order of the hazard’s decreasing severity, except for the categories of the classification table to Subpart 5 of Part 7.Evaluation — order in classification tableWhen a product, mixture, material or substance is evaluated in accordance with the criteria and requirements of a category or subcategory of a hazard class, the evaluation must proceed in accordance with the order of the hazard’s decreasing severity as presented in each classification table. The product, mixture, material or substance must be classified in the category or subcategory for which it meets the criteria. The product, mixture, material or substance that meets the criteria of more than one category or subcategory of the same classification table must be classified, among those categories or subcategories, in the one that represents the most severe hazard.Evaluation not necessary for less severe hazardIf the product, mixture, material or substance is classified in a category or subcategory of a hazard class that represents a more severe hazard in comparison with another category or subcategory of that hazard class in the same classification table, the product, mixture, material or substance need not be evaluated in respect of the category or subcategory that represents a less severe hazard.Prescribed classificationSubject to subsections (4) and (5), any product, mixture, material or substance for which classification in a category or subcategory of a hazard class is prescribed in Schedule 4 is classified in that category or subcategory. The product, mixture, material or substance must also be evaluated in accordance with section 2.1, 2.2 or 2.7 in respect of each of the categories or subcategories of the other hazard classes.Ingredient — more severe hazardIf a product, mixture, material or substance is one for which classification in a category or subcategory of a hazard class is prescribed in Schedule 4, and if it has been mixed with one or more ingredients that are classified in a category or subcategory of the same classification table of the same hazard class that represents a more severe hazard, the mixture as a whole must be classified in the category or subcategory that represents the more severe hazard.Prescribed classification — Subpart 1, 4, 7 or 8 of Part 8A mixture, material or substance — for which classification in a category or subcategory of a classification table of a hazard class set out in Subpart 1, 4, 7 or 8 of Part 8 is prescribed in Schedule 4 — must also be evaluated in accordance with section 2.1 or 2.2, in the case of Subpart 1, 4 or 7 of Part 8, in respect of each of the categories or subcategories of the other classification tables of the same hazard class, and in the case of Subpart 8 of Part 8, in respect of each of the categories of the same classification table.Impurities, stabilizing solvents and stabilizing additives — substanceAny impurities, stabilizing solvents or stabilizing additives that are known to the supplier to be present in a substance and that are classified must be considered for the purpose of classification of the substance if they are present at a concentration above the concentration limit for an ingredient in a mixture set out in a particular category or subcategory of any hazard class.Impurities, stabilizing solvents and stabilizing additives — mixtureAny impurities, stabilizing solvents or stabilizing additives that are known to the supplier to be present in a mixture and that are classified must be considered for the purpose of classification of the mixture if they are present at a concentration above the concentration limit for an ingredient in a mixture set out in a particular category or subcategory of any hazard class.Individually packaged in outer containerIf two or more different and individually packaged products, mixtures, materials or substances, designed to be accessed individually, are packaged together in an outer container for sale or importation, the assemblage of the products, mixtures, materials and substances in the outer container must not be considered as a single product for the purpose of classification, as each product, mixture, material or substance is subject to the classification provisions of this Part.Animal data — not relevant to humansAnimal data from a particular species of animal must not be used for the purpose of classifying a mixture or substance in any of the health hazard classes referred to in Subparts 1 to 10 and 12 of Part 8 when it has been demonstrated conclusively, based on established scientific principles, that the mechanism or mode of action of the mixture or substance in that particular species of animal is not relevant to humans.SOR/2022-272, s. 2Material or SubstanceClassification — material or substanceSubject to sections 2.8 and 2.9, for the purpose of establishing whether a material or substance is classified in a category or subcategory of a hazard class, the material or substance must be evaluated in accordance with established scientific principles, with respect to the criteria and requirements of each category or subcategory of the hazard class as set out in Parts 7 and 8, using available data of the following types, as applicable:in relation to the material or substance itself,results of testing or studies carried out in accordance with the test methods referred to in Part 7 or 8,results of testing or studies carried out in accordance with generally accepted standards of good scientific practice at the time the test or study was carried out,conclusions based on established scientific principles, andcase reports or documented observations; andexcept for Subparts 2 and 3 of Part 8, if the data of the types referred to in paragraph (a) are insufficient to evaluate the material or substance in accordance with the criteria and requirements set out in Parts 7 and 8, in relation to a material or substance that has similar properties,results of testing or studies carried out in accordance with the test methods referred to in Part 7 or 8,results of testing or studies carried out in accordance with generally accepted standards of good scientific practice at the time the test or study was carried out,conclusions based on established scientific principles, andcase reports or documented observations.MixtureClassificationPart 7Subject to section 2.8, for the purpose of establishing whether a mixture is classified in a category or subcategory of a physical hazard class, the mixture must be evaluated, in respect of each category or subcategory of each physical hazard class, using data of the types referred to in subparagraphs 2.1(a)(i) to (iv) in relation to the mixture or, if the data of those types are insufficient to evaluate the mixture in accordance with the criteria and requirements set out in Part 7, using data of the types referred to in subparagraphs 2.1(b)(i) to (iv) in relation to a mixture with similar properties.Part 8Subject to section 2.9, for the purpose of establishing whether a mixture is classified in a category or subcategory of a health hazard class, the mixture must be evaluated, in respect of each category or subcategory of each health hazard class, using data of the types referred to in subparagraphs 2.1(a)(i) to (iv), in relation to the ingredients, the mixture as a whole or a mixture with similar properties, following the order of the provisions, in relation to mixtures, as presented in each Subpart of Part 8.Part 8 — order of provisionsWhen following the order of the provisions in accordance with subsection (2), the mixture must be classified in accordance with the first provision that permits its classification. Once the mixture is classified, the provisions that follow within the same Subpart in relation to mixtures do not apply, except in the case of Subparts 1, 4, 7 and 8 of Part 8.Bridging PrinciplesDefinitionsThe following definitions apply in this section.production batch means a batch that results from a consistent production process using fixed physico-chemical parameters when there is no intention to alter the characteristics of the final product. (lot de fabrication)tested refers to a mixture for which there are data of a type referred to in subparagraph 2.1(a)(i), (ii) or (iv). (testé)Application of bridging principlesIn the case of the health hazard classes set out in Subparts 1 to 10 of Part 8, the bridging principles set out in subsections (3) to (8) must be applied if there is an indication to that effect.DilutionIf a tested mixture that is classified in a category or subcategory of a health hazard class set out in Subparts 1 to 10 of Part 8 is diluted with a diluent, the following applies provided that the diluent is a mixture or substance that, with respect to that health hazard class, has an equivalent or less severe hazard classification than the least hazardous ingredient of the tested mixture and, based on established scientific principles, does not affect the classification of the tested mixture:in the case of a tested mixture that is classified in a category or subcategory of a health hazard class set out in Subparts 1 to 3 of Part 8, either the method referred to in section 8.1.5, 8.2.11 or 8.3.11, as the case may be, must be used to establish whether the diluted mixture must be classified in a category or subcategory of a hazard class, or the diluted mixture must be classified in the same category or subcategory of the health hazard class as the tested mixture; orin all other cases, the diluted mixture must be classified in the same category or subcategory of the health hazard class as the tested mixture.Production batchesThe classification is the same for a mixture in all production batches of that mixture that are manufactured, produced or processed by the same supplier, unless there is a significant variation between the batches that affects the classification of the mixture.Increase in concentration of hazardous ingredientIf the concentration of a hazardous ingredient of a tested mixture is increased, the following applies:in the case of the health hazard classes set out in Subparts 1, 4 and 8 to 10 of Part 8, if the tested mixture is classified in the Category 1 category of the health hazard class, the new mixture resulting from the increased concentration must be classified in the same category of the same health hazard class, without additional evaluation with regard to that hazard class;in the case of the health hazard class set out in Subpart 2 of Part 8,if the tested mixture is classified in the Category 1A subcategory of the health hazard class, the new mixture resulting from the increased concentration must be classified in the same subcategory of the same health hazard class, without additional evaluation with regard to that hazard class, orif the tested mixture does not contain any hazardous ingredient classified in the Category 1 category and is classified in the Category 2 category of the health hazard class, the new mixture resulting from the increased concentration must be classified in the same category of the same health hazard class, without additional evaluation with regard to that hazard class; andin the case of the health hazard class set out in Subpart 3 of Part 8,if the tested mixture is classified in the Category 1 category of the health hazard class, the new mixture resulting from the increased concentration must be classified in the same category of the same health hazard class, without additional evaluation with regard to that hazard class, orif the tested mixture does not contain any hazardous ingredient classified in the Category 1 category and is classified in the Category 2A subcategory of the health hazard class, the new mixture resulting from the increased concentration must be classified in the same subcategory of the same health hazard class, without additional evaluation with regard to that hazard class.InterpolationIn the case of the health hazard classes set out in Subparts 1 to 4 and 8 to 10 of Part 8, when three mixtures (A, B and C) contain identical ingredients — some or all of which are hazardous — if mixtures A and B have been tested and are classified in the same category or subcategory of the same health hazard class and if mixture C has not been tested and has the same hazardous ingredients as mixtures A and B with concentrations intermediate to the concentrations of those hazardous ingredients in mixtures A and B, then mixture C must be classified in the same category or subcategory of the same health hazard class as mixtures A and B.Substantially similar mixturesIf one of the mixtures (ingredient A + ingredient B) or (ingredient C + ingredient B) is a tested mixture that is classified in a category or subcategory of a health hazard class, the other mixture must be classified in the same category or subcategory of the same health hazard class if the following conditions are met:the concentration of ingredient B is the same in both mixtures;the concentration of ingredient A is the same as that of ingredient C; andingredients A and C are classified in the same category or subcategory of the same health hazard class and, based on established scientific principles, do not affect the classification of ingredient B.Aerosols — health hazard classesIn the case of the health hazard classes set out in Subparts 1 to 4, 8 and 9 of Part 8, a mixture to which a propellant has been added and that is contained in an aerosol dispenser must be classified in the same category or subcategory of the same health hazard class as the mixture to which no propellant was added if, based on established scientific principles, the added propellant does not affect the classification of the mixture on spraying.Other PrinciplesSynergistic effectsIn order to establish whether a mixture is classified in a category or subcategory of a health hazard class, if the evaluation of the mixture is carried out in accordance with a provision that requires the use of data available on the ingredients in the mixture, then all data available on the potential occurrence of synergistic effects among the ingredients of the mixture must be used in the evaluation carried out in accordance with section 2.2.Antagonistic effectsIf antagonistic effects among the ingredients of the mixture are considered in order to establish the classification of the mixture in a category or subcategory of a health hazard class in the course of the evaluation carried out in accordance with section 2.2, the data in respect of the antagonistic effects must be conclusive, based on established scientific principles.Concentration limits — lower concentrationIn the case of Subparts 1 to 10 and 12 of Part 8, if an ingredient is present in a mixture at a lower concentration than the concentration limit for a particular category or subcategory of a health hazard class, but still presents the hazard identified by the category or subcategory of that hazard class at that concentration, the mixture must be classified in that category or subcategory.Concentration limits — equivalent or higher concentrationIn the case of Subparts 1 to 10 and 12 of Part 8, subject to subsection 2.4(1), if an ingredient is present in a mixture at an equivalent or higher concentration than the concentration limit for a particular category or subcategory of a health hazard class, but further to evidence based on established scientific principles it does not present the hazard identified by the category or subcategory of that hazard class at that concentration, the mixture need not be classified in that category or subcategory in relation to that specific ingredient.Maximum concentrationIf a mixture with a specific product identifier contains a hazardous ingredient that is not always present at the same concentration, the maximum concentration must be used for the purposes of establishing whether the mixture is classified in a category or subcategory of a health hazard class.ProductClassification — productSubject to section 2.8, to establish whether a product is classified in a category or subcategory of a physical hazard class, it must be evaluated in accordance with section 2.1 or 2.2.Specific RulesSolidsIn the case of the physical hazard classes set out in Subparts 7, 10 to 12 and 14 of Part 7, the data used for the purposes of evaluation of a solid must relate to the solid in the physical form in which it is sold or imported. If the solid is in a physical form that is different from that used to generate the data and the solid in that physical form is liable to display different behaviour, the solid must also be evaluated in that other physical form.Biological availabilityIf it can be shown by conclusive experimental data from scientifically validated methods that the mixture, material or substance is not biologically available, it need not be classified in any health hazard class.LabellingInformation elementsSubject to section 3.6 and for the purposes of paragraphs 13(1)(b) and 14(b) of the Act, the label of a hazardous product or the container in which the hazardous product is packaged must provide, in respect of the hazardous product, the following information elements:the product identifier;the initial supplier identifier;subject to subsections (2), (3) and (4) to (5), for each category or subcategory in which the hazardous product is classified, with the exception of the categories referred to in paragraphs (c.1) to (d), the information elements, namely, the symbol, signal word, hazard statement and precautionary statement, that are specified for that category or subcategory in section 3 of Annex 3 of the GHS;subject to subsections (2) and (3.1), in the case of a hazardous product that is classified in the category “Chemicals Under Pressure – Category 1” or “Chemicals Under Pressure – Category 2”, the symbol, signal word, hazard statement and precautionary statement specified for that category in section 3 of Annex 3 of the United Nations document entitled Globally Harmonized System of Classification and Labelling of Chemicals (GHS), Eighth Revised Edition;subject to subsections (2) and (3.1), in the case of a hazardous product that is classified in the category “Chemicals Under Pressure – Category 3”, the symbol, signal word and precautionary statement specified for that category in section 3 of Annex 3 of the United Nations document entitled Globally Harmonized System of Classification and Labelling of Chemicals (GHS), Eighth Revised Edition, as well as the hazard statement “Chemical under pressure: May explode if heated/Produit chimique sous pression : peut exploser sous l’effet de la chaleur”;subject to subsections (2) to (4), for each category set out in Subparts 17 to 20 of Part 7 and in Subparts 11 and 12 of Part 8 in which the hazardous product is classified,the information elements that are specified for that category in Schedule 5, andany precautionary statements that are applicable to the hazardous product in terms ofgeneral precautionary statements,prevention precautionary statements,response precautionary statements,storage precautionary statements, anddisposal precautionary statements;in the case of a hazardous product classified in a category of Subpart 1 of Part 8 and to which paragraph 8.1.6(b) applies, the supplemental label element “[Insert the total concentration in percentage of ingredients with unknown acute toxicity] % of the mixture consists of an ingredient or ingredients of unknown acute toxicity/[Insérez la concentration totale en pourcentage d’ingrédients ayant une toxicité aiguë inconnue] % du mélange consiste en ingrédients de toxicité aiguë inconnue”;in the case of a hazardous product that is classified as an acute toxicant and that, upon contact with water, releases a gaseous substance that has an LC50 that falls into one of the ranges indicated in Table 3 to subsection 8.1.1(3), the supplemental label elements that consist of the following hazard statements:in the case of a released gaseous substance that is classified in Category 1 or 2, “In contact with water, releases gases which are fatal if inhaled/Au contact de l’eau, libère des gaz mortels en cas d’inhalation”,in the case of a released gaseous substance that is classified in Category 3, “In contact with water, releases gases which are toxic if inhaled/Au contact de l’eau, libère des gaz toxiques en cas d’inhalation”, orin the case of a released gaseous substance that is classified in Category 4, “In contact with water, releases gases which are harmful if inhaled/Au contact de l’eau, libère des gaz nocifs en cas d’inhalation”; andin the case of a hazardous product that is classified in the category “Acute Toxicity (Inhalation) — Category 1”, “Acute Toxicity (Inhalation) — Category 2”, “Acute Toxicity (Inhalation) — Category 3” or “Acute Toxicity (Inhalation) — Category 4” further to subsection 8.1.1(2), the supplemental label elements that consist of the following hazard statements:in the case of a released gaseous substance that is classified in Category 1 or 2, “In contact with water, releases gases which are fatal if inhaled/Au contact de l’eau, libère des gaz mortels en cas d’inhalation”,in the case of a released gaseous substance that is classified in Category 3, “In contact with water, releases gases which are toxic if inhaled/Au contact de l’eau, libère des gaz toxiques en cas d’inhalation”, orin the case of a released gaseous substance that is classified in Category 4, “In contact with water, releases gases which are harmful if inhaled/Au contact de l’eau, libère des gaz nocifs en cas d’inhalation”.Codes or instructionsThe information elements required by paragraphs (1)(c) to (c.2) need not include alphanumeric codes and the information elements required by paragraphs (1)(c) to (d) must not include instructions that are for the exclusive use of the competent authority, as defined in the GHS, or the supplier.Substitution by pictogramThe pictogram associated with a symbol in Schedule 3 must be substituted for the symbol that is specified for a category or subcategory in section 3 of Annex 3 of the GHS or for a category in Schedule 5.Chemicals under pressureIn the case of a hazardous product that is classified in a category of the “Chemicals Under Pressure” hazard class, the pictogram associated with a symbol in Schedule 3 must be substituted for the symbol that is specified for that category in section 3 of Annex 3 of the United Nations document entitled Globally Harmonized System of Classification and Labelling of Chemicals (GHS), Eighth Revised Edition.Hazard statement — Specific Target Organ Toxicity — Single ExposureIn the case of a hazardous product that is classified in the category “Specific Target Organ Toxicity — Single Exposure — Category 3” of the hazard class “Specific Target Organ Toxicity — Single Exposure”, the hazard statement specified for that category in section 3 of Annex 3 of the GHS that relates to the effects for which the product was classified must be used. If the hazardous product causes narcotic effects and respiratory tract irritation, as those terms are defined in Subpart 8 of Part 8, then both hazard statements must be used.Precautionary statement — Pyrophoric Liquids and Pyrophoric SolidsIn the case of a hazardous product that is classified in the category “Pyrophoric Liquids – Category 1” or in the category “Pyrophoric Solids – Category 1”, in addition to the information elements that are specified for those categories in section 3 of Annex 3 of the GHS, the following precautionary statement must be used:if the contents of the hazardous product are handled and stored under inert gas, “Handle and store contents under inert gas/Manutentionner et stocker le contenu sous gaz inerte”; orif the contents of the hazardous product are handled and stored under a liquid or gas other than inert gas, “Handle and store contents under [insert the name of the liquid or gas]/Manutentionner et stocker le contenu sous [insérez le nom du liquide ou du gaz]”.Hazard statement — Acute Toxicity (Inhalation)In the case of a hazardous product that is classified in the category “Acute Toxicity (Inhalation) — Category 1”, “Acute Toxicity (Inhalation) — Category 2”, “Acute Toxicity (Inhalation) — Category 3” or “Acute Toxicity (Inhalation) — Category 4 ” further to subsection 8.1.1(2), the hazard statement specified for that category in section 3 of Annex 3 of the GHS need not be used on the label.Information elements for certain categories or subcategoriesThe information elements, namely, the symbol, signal word, hazard statement and precautionary statement, specified in section 3 of Annex 3 of the GHS that are to be used for hazardous products classified in the categories or subcategories below are as follows:[Repealed, SOR/2022-272, s. 3][Repealed, SOR/2022-272, s. 3][Repealed, SOR/2022-272, s. 3][Repealed, SOR/2022-272, s. 3]if the hazardous product is classified in the category “Skin Corrosion — Category 1”, the information elements specified for the subcategory “Skin Corrosion/Irritation” Hazard category 1A;if the hazardous product is classified in the subcategory “Skin Corrosion — Category 1A”, in the subcategory “Skin Corrosion — Category 1B” or in the subcategory “Skin Corrosion — Category 1C”, the information elements specified for the subcategory “Skin Corrosion/Irritation” Hazard category 1A to 1C;if the hazardous product is classified in the category “Skin Irritation — Category 2”, the information elements specified for the category “Skin Corrosion/Irritation” Hazard category 2;if the hazardous product is classified in the category “Serious Eye Damage — Category 1”, the information elements specified for the category “Eye Damage/Irritation” Hazard category 1;if the hazardous product is classified in the category “Eye Irritation — Category 2”, the information elements specified for the subcategory “Eye Damage/Irritation” Hazard category 2A;if the hazardous product is classified in the subcategory “Eye Irritation — Category 2A” or in the subcategory “Eye Irritation — Category 2B”, the information elements specified, respectively, for the subcategory “Eye Damage/Irritation” Hazard category 2A or the subcategory “Eye Damage/Irritation” Hazard category 2B;if the hazardous product is classified in the category “Respiratory Sensitizer — Category 1”, in the subcategory “Respiratory Sensitizer — Category 1A” or in the subcategory “Respiratory Sensitizer — Category 1B”, the information elements specified for the category or subcategory “Sensitization — Respiratory” Hazard category 1, 1A or 1B;if the hazardous product is classified in the category “Skin Sensitizer — Category 1”, in the subcategory “Skin Sensitizer — Category 1A” or in the subcategory “Skin Sensitizer — Category 1B”, the information elements specified for the category or subcategory “Sensitization — Skin” Hazard category 1, 1A or 1B;if the hazardous product is classified in the subcategory “Germ Cell Mutagenicity — Category 1A” or in the subcategory “Germ Cell Mutagenicity — Category 1B”, the information elements specified for the category “Germ Cell Mutagenicity” Hazard category 1;if the hazardous product is classified in the subcategory “Carcinogenicity — Category 1A” or in the subcategory “Carcinogenicity — Category 1B”, the information elements specified for the category “Carcinogenicity” Hazard category 1; andif the hazardous product is classified in the subcategory “Reproductive Toxicity — Category 1A” or in the subcategory “Reproductive Toxicity — Category 1B”, the information elements specified for the category “Reproductive Toxicity” Hazard category 1.SOR/2022-272, s. 3PictogramsAny pictogram required to be provided on a label must, except with respect to size, be an exact reproduction of that pictogram as set out in column 3 of Schedule 3 and must,except for the pictogram for “Biohazardous Infectious Materials”, have a black symbol on a white background with a red border in the shape of a square set on one of its points; andin the case of the pictogram for “Biohazardous Infectious Materials”, have a black symbol on a white background with a black border in the shape of a circle.Combined precautionary statementsThe precautionary statements that are required to be provided on a label may be combined if the combination contains the same information as would have been conveyed by each of the individual precautionary statements.Non-applicable precautionary statementsIf a precautionary statement that is required to be provided on a label does not apply in a particular case with regard to the normal conditions of use, handling and storage of the hazardous product, it may be omitted.Combined hazard statementsThe hazard statements that are required to be provided on a label may be combined if the combination contains the same information as would have been conveyed by each of the individual hazard statements.SOR/2022-272, s. 4Information elements of labelThe pictogram, signal word and hazard statement must be grouped together on the label.LegibilityThe information elements of the label of the hazardous product or container in which it is packaged must be clearly and prominently displayed on a surface that is visible under normal conditions of use, easily legible without the aid of any device other than corrective lenses and contrasted with any other information on the hazardous product or the container.DurabilityThe information elements of the label of the hazardous product or container in which it is packaged must, under normal conditions of transport and use, remain affixed to, printed or written on or attached to the hazardous product or the container and remain legible.Specific rule — signal wordIf there is a requirement to provide the signal word “Danger” on a label, any requirement to provide the signal word “Warning” does not apply.Specific rule — hazard statementIf there is a requirement to provide the hazard statement “Causes severe skin burns and eye damage” on a label, any requirement to provide the hazard statement “Causes serious eye damage” does not apply.Specific rule — symbolIn the case of the symbols specified below, the following apply:if there is a requirement to provide the “skull and crossbones” symbol on a label, any requirement to provide the “exclamation mark” symbol to indicate acute toxicity does not apply;if there is a requirement to provide the “corrosion” symbol on a label, any requirement to provide the “exclamation mark” symbol to indicate skin or eye irritation does not apply; andif there is a requirement to provide the “health hazard” symbol on a label to indicate respiratory sensitization, any requirement to provide the “exclamation mark” symbol to indicate skin sensitization or skin or eye irritation does not apply.SOR/2022-272, s. 5Safety Data SheetInformation elementsSubject to section 4.7 and for the purposes of paragraphs 13(1)(a) and 14(a) of the Act, the safety data sheet of a hazardous product must provide, in respect of the hazardous product, the following information elements:the headings set out in column 1 of Schedule 1, in the order they are presented, including the corresponding item number, which is to be placed immediately before the heading;subject to sections 4.4.1 and 4.5, the content of the specific information elements set out in paragraphs 3(1)(a) and (2)(a) and (d) of Schedule 1 for the heading for item 3 and, for each heading of that Schedule, if the information is available and applicable, the content of the other specific information elements of that Schedule, including the unit of measure, if applicable, taking into account the following:if any of the information — except that required by paragraphs 3(1)(a) and (2)(a) and (d) of that Schedule — is not available or not applicable, an indication to that effect must be clearly stated in lieu of the required specific information element, andin the case of a mixture, the information provided under the heading for item 11 of Schedule 1 must be information that is available on the mixture as a whole, and if information is not available on the mixture as a whole, it must be information that is available on the hazardous ingredients in the mixture, together with a clear indication of the chemical name of the hazardous ingredient to which the information pertains; andunder any applicable heading, all additional hazard information that is available with respect tothe hazardous product, anda product, mixture, material or substance that has similar properties, including any evidence based on established scientific principles, if that information is applicable to the normal conditions of use of the hazardous product and is not redundant, indicated alongside an identification of the product, mixture, material or substance that has similar properties.Items 12 to 15 of Schedule 1Despite subsection (1), under each heading set out for items 12 to 15 of Schedule 1, the content of the specific information elements in that Schedule may be omitted.Biohazardous Infectious Materials — additional information elementsThe following information elements must be provided, immediately following the information elements required by subsection (1), on the safety data sheet of a hazardous product that is classified in a category of the hazard class “Biohazardous Infectious Materials”:the headings set out in Schedule 2, in the order they are presented;under each heading, the name of each specific information element set out in column 2 in respect of that heading in the order they are presented; andunder the name of each specific information element, the content of the information element, if the information is available and applicable, including the unit of measure, if applicable, taking into account the following:if any of the information is not available or not applicable, an indication to that effect must be clearly stated in lieu of the required information, andany information provided under one heading of the safety data sheet need not be repeated under any other heading.More than one biohazardous infectious materialIn the case where a mixture contains more than one ingredient that is classified as a biohazardous infectious material, the information required by subsection (3) must be provided in distinct parts on the safety data sheet, sequentially, for each biohazardous infectious material.SOR/2022-272, s. 6Instructions for use — new material or substanceIn the case of a hazardous product for which instructions for use, provided at the time of the sale or importation, require its combination with one or more products, mixtures, materials or substances resulting in the creation of one or more new materials or substances that present one or more new or more severe hazards not already identified on the safety data sheet of the hazardous product, the safety data sheet must also provide the following information elements, in respect of each new material or substance and clearly indicate that they pertain to that new material or substance:the nature of the new or more severe hazard; andthe content of the applicable specific information elements set out in items 4 to 11, column 2, of Schedule 1, for each corresponding heading, that is available.Placement of information elementsDespite subsection 4(1), the information elements required by subsection (1) may appear anywhere on the safety data sheet.Identical identifiersThe product identifier, the initial supplier identifier and, if applicable, any replacement information required under subsection 5.7(9) or (10) that are provided on the safety data sheet of a hazardous product must be identical to those provided on the label.SOR/2022-272, s. 7Concentration unitsIf the concentration of a material or substance in a hazardous product is expressed as a percentage on the safety data sheet, the units used to calculate the percentage must be provided.Most hazardous concentrationIf ingredients in a mixture that is a hazardous product are present in a range of concentrations, the information provided on the safety data sheet must be based on data available that correspond to the most hazardous concentration of each ingredient in the mixture, whether those data pertain to an ingredient or the mixture as a whole.Concentration range — material or substance always present at the same concentrationIf the concentration of a material or substance in a hazardous product is required to be provided on a safety data sheet and the material or substance is always present at the same concentration, the safety data sheet must providethe actual concentration of the material or substance in the hazardous product;one of the concentration ranges set out in subsection (3) within which the actual concentration of the material or substance in the hazardous product falls; ora concentration range of the material or substance in the hazardous product that falls entirely within one of the concentration ranges set out in subsection (3).Actual concentration within more than one concentration rangeFor the purposes of paragraphs (1)(b) and (c), if the actual concentration of a material or substance in a hazardous product falls within more than one of the concentration ranges set out in subsection (3), then any one of those ranges or a range that falls entirely within any one of those ranges may be provided on the safety data sheet.Concentration rangesFor the purposes of paragraphs (1)(b) and (c) and subsection (2), the concentration ranges are the following:from 0.1 to 1%;from 0.5 to 1.5%;from 1 to 5%;from 3 to 7%;from 5 to 10%;from 7 to 13%;from 10 to 30%;from 15 to 40%;from 30 to 60%;from 45 to 70%;from 60 to 80%;from 65 to 85%; andfrom 80 to 100%.Statement — trade secretIf the safety data sheet provides a concentration range further to paragraph (1)(b) or (c), it must also provide, immediately following the concentration range, a statement to the effect that the actual concentration is withheld as a trade secret.SOR/2018-68, s. 1SOR/2022-272, s. 8Concentration range — material or substance not always present at the same concentrationIf the concentration of a material or substance in a hazardous product is required to be provided on a safety data sheet and the material or substance is not always present at the same concentration, the safety data sheet must providethe actual concentration range of the material or substance in the hazardous product;one of the concentration ranges set out in subsection (3) within which the actual concentration range of the material or substance in the hazardous product falls entirely;a concentration range of the material or substance in the hazardous product that falls entirely within one of the concentration ranges set out in subsection (3); orif the actual concentration range of the material or substance in the hazardous product is equal to or greater than 0.1% but less than or equal to 30%, and the actual concentration range does not fall entirely within any of the concentration ranges set out in subsection (3), a concentration range that is created by combining two consecutive ranges from those set out in paragraphs (3)(a) to (g), provided that the combined concentration range does not include any range that falls entirely outside the actual concentration range in which the material or substance is present in the hazardous product.Actual concentration range within more than one concentration rangeFor the purposes of paragraphs (1)(b) and (b.1), if the actual concentration range of a material or substance in a hazardous product falls entirely within more than one of the concentration ranges set out in subsection (3), then any one of those ranges or a range that falls entirely within any one of those ranges may be provided on the safety data sheet.Concentration rangesFor the purposes of paragraphs (1)(b) to (c) and subsection (2), the concentration ranges are the following:from 0.1 to 1%;from 0.5 to 1.5%;from 1 to 5%;from 3 to 7%;from 5 to 10%;from 7 to 13%;from 10 to 30%;from 15 to 40%;from 30 to 60%;from 45 to 70%;from 60 to 80%;from 65 to 85%; andfrom 80 to 100%.Statement — trade secretIf the safety data sheet provides a concentration range further to paragraph (1)(b), (b.1) or (c), it must also provide, immediately following that concentration range, a statement to the effect that the actual concentration range is withheld as a trade secret.SOR/2018-68, s. 1SOR/2022-272, s. 9Combined precautionary statementsThe precautionary statements that are required to be provided on a safety data sheet may be combined if the combination contains the same information as would have been conveyed by each of the individual precautionary statements.Non-applicable precautionary statementsIf a precautionary statement that is required to be provided on a safety data sheet does not apply in a particular case with regard to the normal conditions of use, handling and storage of the hazardous product, it may be omitted.Combined hazard statementsThe hazard statements that are required to be provided on a safety data sheet may be combined if the combination contains the same information as would have been conveyed by each of the individual hazard statements.SOR/2022-272, s. 10Specific rule — signal wordIf there is a requirement to provide the signal word “Danger” on a safety data sheet, any requirement to provide the signal word “Warning” does not apply.Specific rule — hazard statementIf there is a requirement to provide the hazard statement “Causes severe skin burns and eye damage” on a safety data sheet, any requirement to provide the hazard statement “Causes serious eye damage” does not apply.Hazard statement — Acute Toxicity (Inhalation)In the case of a hazardous product that is classified in the category “Acute Toxicity (Inhalation) — Category 1”, “Acute Toxicity (Inhalation) — Category 2”, “Acute Toxicity (Inhalation) — Category 3” or “Acute Toxicity (Inhalation) — Category 4” further to subsection 8.1.1(2), the hazard statement specified for that category in section 3 of Annex 3 of the GHS need not be used on the safety data sheet.Specific rule — symbolIn the case of the symbols specified below, the following apply:if there is a requirement to provide the “skull and crossbones” symbol on a safety data sheet, any requirement to provide the “exclamation mark” symbol to indicate acute toxicity does not apply;if there is a requirement to provide the “corrosion” symbol on a safety data sheet, any requirement to provide the “exclamation mark” symbol to indicate skin or eye irritation does not apply; andif there is a requirement to provide the “health hazard” symbol on a safety data sheet to indicate respiratory sensitization, any requirement to provide the “exclamation mark” symbol to indicate skin sensitization or skin or eye irritation does not apply.SOR/2022-272, s. 10ExceptionsDefinition of laboratory sampleIn this section, laboratory sample means a sample of a hazardous product that is packaged in a container that contains less than 10 kg of the hazardous product and that is intended solely to be tested in a laboratory, but does not include a sample that is to be usedby the laboratory for testing other products, mixtures, materials or substances; orfor educational or demonstration purposes.Sale or importation — biohazardous infectious materials — safety data sheetSubject to subsection (3), the sale or importation of a laboratory sample that is classified only in the category “Biohazardous Infectious Materials — Category 1” is exempt from the application of paragraphs 13(1)(a) and (a.1) and 14(a) of the Act.Transfer of possession — biohazardous infectious materials — safety data sheet and labelThe transfer of possession of a laboratory sample for a specific purpose, without transferring ownership, if that laboratory sample is classified only in the category “Biohazardous Infectious Materials — Category 1”, is exempt from the application of section 13 of the Act.Transfer of possession — safety data sheetThe transfer of possession of a laboratory sample for a specific purpose, without transferring ownership, if that laboratory sample is one of the following types, is exempt from the application of paragraphs 13(1)(a) and (a.1) of the Act:a laboratory sample for which the chemical name and concentration of the hazardous product or its ingredients are not known; ora laboratory sample for which the supplier has not offered or exposed the hazardous product for transfer of ownership.Sale or importation — biohazardous infectious materials — labelSubject to subsection (3), the sale or importation of a laboratory sample that is classified only in the category “Biohazardous Infectious Materials — Category 1” is exempt from the application of paragraph 3(1)(d) if the label provides the chemical name or generic chemical name of any material that is in the hazardous product and that is classified as a biohazardous infectious material, if known by the supplier, and the statement “Hazardous Laboratory Sample. For hazard information or in an emergency, call/Échantillon pour laboratoire de produit dangereux. Pour obtenir des renseignements sur les dangers ou en cas d’urgence, composez”, followed by an emergency telephone number for the purpose of obtaining the information that must be provided on the safety data sheet of the hazardous product.Transfer of possession — labelThe transfer of possession of a laboratory sample for a specific purpose, without transferring ownership, is exempt from the application of paragraphs 3(1)(c) to (d) ifthe laboratory sample is one of the following types:a laboratory sample that is a substance for which the chemical name is not known,a laboratory sample that is a mixture for which the chemical name of one or more of its ingredients is not known or for which the concentration of one or more of its ingredients is not known, ora laboratory sample in respect of which the supplier has not offered or exposed the hazardous product for transfer of ownership; andthe label of the laboratory sample provides the following information:the statement “Hazardous Laboratory Sample. For hazard information or in an emergency, call/Échantillon pour laboratoire de produit dangereux. Pour obtenir des renseignements sur les dangers ou en cas d’urgence, composez”, followed by an emergency telephone number for the purpose of obtaining the information that must be provided on the safety data sheet of the hazardous product,if the laboratory sample is a substance, the chemical name or generic chemical name of the substance, if known by the supplier, andif the laboratory sample is a mixture, the chemical name or generic chemical name of any ingredient that is in the laboratory sample and that is referred to in subsection 3(2) of Schedule 1, if known by the supplier.SOR/2022-272, s. 11Mixture of radioactive nuclides and non-radioactive carriers — section 13 or 14 of ActThe sale or importation of a hazardous product that is a mixture of one or more radioactive nuclides and one or more non-radioactive carriers is exempt from the application of section 13 or 14 of the Act if the carrieris present in an amount that isin the case of a liquid or gaseous carrier, less than or equal to 1.0 ml, orin the case of a solid carrier, less than or equal to 1.0 g; andis notclassified in any category or subcategory of the “Carcinogenicity”, “Germ Cell Mutagenicity”, “Reproductive Toxicity” or “Biohazardous Infectious Materials” hazard class,classified in the category “Acute Toxicity (Oral) — Category 1” or “Acute Toxicity (Dermal) — Category 1” of the “Acute Toxicity” hazard class, orclassified in the category “Acute Toxicity (Inhalation) — Category 1” or “Acute Toxicity (Inhalation) — Category 2” of the “Acute Toxicity” hazard class.Mixture of radioactive nuclides and non-radioactive carriers — paragraph 13(1)(b) or 14(b) of ActThe sale or importation of a hazardous product that is a mixture of one or more radioactive nuclides and one or more non-radioactive carriers is exempt from the application of paragraph 13(1)(b) or 14(b) of the Act in respect of the requirement to have a label on the inner container of the hazardous product if the hazardous product is packaged in more than one container and the outer container has a label that provides the information elements required by Part 3.Mixture of radioactive nuclides and non-radioactive carriersThe sale or importation of a hazardous product that is a mixture of one or more radioactive nuclides and one or more non-radioactive carriers is exempt from the application ofparagraph 3(1)(b); andparagraphs 3(1)(c) to (c.2) and subparagraph 3(1)(d)(ii), in respect of the requirement to provide any precautionary statement on the label of the hazardous product or the container in which it is packaged.SOR/2022-272, s. 12Outer containerThe sale or importation of a hazardous product is exempt from the application of paragraph 13(1)(b) or 14(b) of the Act in respect of the requirement to have a label on the outer container of the hazardous product ifthe label on the inner container is visible and legible through the outer container under normal conditions of storage and handling; orthe outer container has a label that meets the requirements set out in the Transportation of Dangerous Goods Regulations.Label — outer container — at least two hazardous productsIn the case of an outer container in which at least two different hazardous products are packaged, subsection 3(1) does not apply if the label provides the following information elements:the product identifier for each hazardous product contained in the outer container;the initial supplier identifier;subject to subsection 3.6(3), the pictogram set out in column 3 of Schedule 3 designated for each category or subcategory in which each hazardous product contained in the outer container is classified;the precautionary statement applicable to the storage of each of the hazardous products contained in the outer container; andthe statement “See individual product labels for signal words, hazard statements and precautionary statements/Voir les étiquettes sur chacun des produits pour les mentions d’avertissement, les mentions de danger et les conseils de prudence”.Small-capacity containers — 100 ml or lessThe sale or importation of a hazardous product in a container that has a capacity of less than or equal to 100 ml, including any subsequent container of the same capacity in which that first container is packaged, is exempt from the application of paragraphs 3(1)(c) to (c.2) and subparagraph 3(1)(d)(i) or (ii) in respect of the requirement to provide any precautionary statement or hazard statement on the label of the hazardous product or the container.Small-capacity containers — 3 ml or lessThe sale or importation of a hazardous product in a container that has a capacity of less than or equal to 3 ml is exempt from the application of section 3.5 in respect of normal conditions of use if the label interferes with the normal use of the hazardous product.SOR/2022-272, s. 13Definition of bulk shipmentIn this section, bulk shipment means a shipment of a hazardous product that is contained in any of the following, without intermediate containment or intermediate packaging:a vessel that has a water capacity equal to or greater than 450 l;a freight container, road vehicle, railway vehicle or portable tank;the hold of a ship; ora pipeline.Bulk shipments and unpackaged hazardous productsThe sale or importation of a bulk shipment or a hazardous product without packaging of any sort is exempt from the application of paragraph 13(1)(b) or 14(b) of the Act.Definition of complex mixtureIn this section, complex mixture means a mixture that has a commonly known generic name and that isnaturally occurring;a fraction of a naturally occurring mixture that results from a separation process; ora modification of a naturally occurring mixture or a modification of a fraction of a naturally occurring mixture that results from a chemical modification process.Complex mixtureThe sale or importation of a hazardous product that is a complex mixture is exempt from the application of paragraph 4(1)(b) in respect of the requirements set out in paragraphs 3(2)(a) and (d) of Schedule 1, and in paragraphs 3(2)(b) and (c) of that Schedule, if that information is available and applicable, in relation to the ingredients of the complex mixture, if the commonly known generic name of the complex mixture is provided for item 3 of the safety data sheet.Complex mixture — ingredientSubject to subsection (4), the sale or importation of a hazardous product that contains an ingredient that is a complex mixture is exempt from the application of paragraph 4(1)(b) in respect of the requirements set out in paragraphs 3(2)(a) and (d) of Schedule 1, and in paragraphs 3(2)(b) and (c) of that Schedule, if that information is available and applicable, in relation to the ingredients of the complex mixture if the complex mixture, individually, is classified in a category or subcategory of a health hazard class and the commonly known generic name of the complex mixture and its concentration in the hazardous product are provided for item 3 of the safety data sheet.Concentration results in classificationIf the complex mixture is present at a concentration that results in the product being classified in a category or subcategory of any health hazard class further to subsection 2.5(1), the commonly known generic name and concentration of the complex mixture must be provided on the safety data sheet of the hazardous product.DefinitionsThe following definitions apply in this section.first supplier means a supplier who is exempted from the requirement to disclose the information specified in subsection 11(1) of the Hazardous Materials Information Review Act, by virtue of that Act. (premier fournisseur)subsequent supplier means a supplier who sells or imports a hazardous product that is the subject of an exemption granted to the first supplier from the requirement to disclose the information specified in subsection 11(1) of the Hazardous Materials Information Review Act. (fournisseur subséquent)Confidential informationIf any information is the subject of an exemption under the Hazardous Materials Information Review Act, the information must be replaced by the information required under subsection (3) or (4).Subsection 11(1) of Hazardous Materials Information Review ActA supplier who, under subsection 11(1) of the Hazardous Materials Information Review Act, files a claim for exemption from a requirement to disclose information in respect of a hazardous product on a safety data sheet or on a label must, in respect of the sale or importation of the hazardous product, provide on the safety data sheet and, if applicable, on the label of the hazardous product or container in which the hazardous product is packaged a statement that a claim was filed, the date that the claim was filed and the registry number assigned to the claim under the Hazardous Materials Information Review Act untilin the case that an order was issued by the Minister under subsection 14(1) or 18(1) of the Hazardous Materials Information Review Act, the end of the period that begins on the day after the day on which all judicial reviews and appeals are exhausted and does not exceed the period specified in the order; orin any other case, the end of the period not exceeding 30 days after the day on which all judicial reviews and appeals are exhausted.Information to be disclosedA supplier who receives notice of a determination made under the Hazardous Materials Information Review Act that their claim or a portion of their claim for exemption from a requirement to disclose information in respect of a hazardous product on a safety data sheet or a label is valid must, during the period beginning no later than the end of the applicable period specified in subsection (3) and on compliance with any order issued under subsection 14(1) or 18(1) of the Hazardous Materials Information Review Act, if applicable, and ending on the last day of the exemption period, in respect of the sale or importation of the hazardous product, provide on the safety data sheet and, if applicable, on the label of the hazardous product or container in which the hazardous product is packaged the following information:a statement that an exemption has been granted;the date of the determination granting the exemption; andthe registry number assigned to the claim under the Hazardous Materials Information Review Act.Non-application — paragraphs 3(1)(a) to (d) or (2)(a) to (c) of Schedule 1The sale or importation of a hazardous product is exempt from the application of paragraph 4(1)(b) in respect of the requirements set out in paragraph 3(1)(a) or (2)(a) of Schedule 1 and, if the information is available and applicable, in paragraphs 3(1)(b) to (d) or 2(b) and (c) of that Schedule, if it is the subject of a claim for exemption under paragraph 11(1)(a) of the Hazardous Materials Information Review Act and if the generic chemical name of the material, substance or ingredient is provided for item 3 of the safety data sheet.Non-application — paragraph 3(2)(d) of Schedule 1Paragraph 3(2)(d) of Schedule 1 does not apply in respect of a hazardous product that is the subject of a claim for exemption under subparagraph 11(1)(b)(iii) of the Hazardous Materials Information Review Act.Sale or importation — paragraphs 3(1)(a) to (d) or (2)(a) to (c) of Schedule 1The sale or importation of a hazardous product by a subsequent supplier is exempt from the application of paragraph 4(1)(b) in respect of the requirements set out in paragraph 3(1)(a) or (2)(a) of Schedule 1, and, if the information is available and applicable, in paragraphs 3(1)(b) to (d) or 2(b) and (c) of that Schedule, ifthe first supplier is exempt from those requirements;the information is unknown to the subsequent supplier, or the information is known to the subsequent supplier but the subsequent supplier has obtained the information in confidence, express or implied, and is obligated, expressly or implicitly, by contract or a relationship based on trust and confidence, or otherwise by law or equity, to maintain the confidentiality of the information; andthe safety data sheet for the hazardous product that the subsequent supplier provides on the sale, or obtains or prepares on the importation, provides in lieu of the information referred to in paragraph 3(1)(a) or (2)(a) of Schedule 1, and, if the information is available and applicable, in paragraphs 3(1)(b) to (d) or 2(b) and (c) of that Schedule,the information referred to in subsection (3) or (4) in respect of,if the subsequent supplier is exempted from the requirement to provide information that could be used to identify the first supplier, that exemption, orin any other case, the exemption of the first supplier, with the words “other supplier/autre fournisseur” in parentheses after that information, andthe generic chemical name of the material, substance or ingredient as provided by the first supplier.Sale or importation — paragraph 3(2)(d) of Schedule 1The sale or importation of a hazardous product by a subsequent supplier is exempt from the application of paragraph 4(1)(b) in respect of the requirement set out in paragraph 3(2)(d) of Schedule 1, ifthe first supplier is exempt from that requirement;the information is unknown to the subsequent supplier, or the information is known to the subsequent supplier but the subsequent supplier has obtained the information in confidence, express or implied, and is obligated, expressly or implicitly, by contract or a relationship based on trust and confidence, or otherwise by law or equity, to maintain the confidentiality of the information; andthe safety data sheet for the hazardous product that the subsequent supplier provides on the sale, or obtains or prepares on the importation, provides in lieu of the information referred to in paragraph 3(2)(d) of Schedule 1the information referred to in subsection (3) or (4) in respect of,if the subsequent supplier is exempted from the requirement to provide information that could be used to identify the first supplier, that exemption, orin any other case, the exemption of the first supplier, with the words “other supplier/autre fournisseur” in parentheses after that information, andsubject to sections 4.4.1 and 4.5, the concentration of the first supplier’s hazardous product that is in the subsequent supplier’s hazardous product.Safety data sheet and label — confidential product identifier — paragraphs 3(1)(a) and 4(1)(b)Paragraph 3(1)(a) and the requirement in paragraph 4(1)(b) in relation to paragraph 1(a) of Schedule 1, if the information is available and applicable, do not apply in respect of the sale of a hazardous product to an employer who is exempt under the Hazardous Materials Information Review Act or under the laws of a province from the requirement to disclose the product identifier of a hazardous product if that information is replaced on the label and safety data sheet by:the code name or code number specified by the supplier; andthe information referred to in subsection (3) or (4) in respect of the employer’s claim for exemption under the Hazardous Materials Information Review Act or, if that information is not available, the information required to be provided under the laws of the province.Safety data sheet and label — confidential supplier identifier — paragraphs 3(1)(b) and 4(1)(b)Paragraph 3(1)(b) and the requirement in paragraph 4(1)(b) in relation to paragraph 1(d) of Schedule 1, if the information is available and applicable, do not apply in respect of the sale of a hazardous product to an employer who is exempt under the Hazardous Materials Information Review Act or under the laws of a province from the requirement to disclose any information that could be used to identify the supplier of the hazardous product if that information is replaced on the label and the safety data sheet byif available, the information referred to in subsection (3) or (4) in respect of the employer’s claim for exemption under the Hazardous Materials Information Review Act; orif the information referred to in paragraph (a) is not available, the information required to be provided under the laws of the province.Safety data sheet — sale to employerThe sale of a hazardous product to an employer is exempt from the requirement to disclose information – other than the product identifier and initial supplier identifier – on the safety data sheet that could be the subject of a claim for exemption under subsection 11(2) of the Hazardous Materials Information Review Act ifthe employer is exempt, under that Act or the laws of a province, from the requirement to disclose that information in respect of the hazardous product; andthe safety data sheet of the hazardous product provided in respect of that sale provides in lieu of that informationif available, the information referred to in subsection (3) or (4) in respect of the employer’s claim for exemption under that Act, orif the information referred to in subparagraph (i) is not available, an emergency telephone number of the employer that will enable a health professional to obtain any information referred to in subsection 4(1) that is in the possession of the employer for the purpose of making a medical diagnosis of, or rendering medical treatment to, a person in an emergency.SOR/2020-38, s. 1SOR/2022-272, s. 14Subsequent sale by supplier — safety data sheetThe sale of a hazardous product by a supplier to whom the hazardous product was sold is exempt from the application of paragraph 4(1)(b) in respect of the requirement set out in paragraph 1(d) of Schedule 1 to provide the initial supplier identifier on the safety data sheet if their name, address and telephone number are provided on the safety data sheet.Subsequent sale by supplier — labelThe sale of a hazardous product by a supplier to whom the hazardous product was sold is exempt from the application of paragraph 3(1)(b) in respect of the requirement to provide the initial supplier identifier on the label if their name, address and telephone number are provided on the label.Following supplierIf the initial supplier identifier referred to in subsection (1) or (2) has been replaced by the name, address and telephone number of a supplier to whom the hazardous product has been sold, any following supplier of the hazardous product may replace that information with their own name, address and telephone number.Importation for use in own work place — safety data sheetIf an importer imports a hazardous product from a foreign supplier for use in their own work place in Canada and obtains a safety data sheet from the foreign supplier, the importer is exempt from the requirement to provide, on the safety data sheet, the specific information element set out in paragraph 1(d) of Schedule 1 if the name, address and telephone number of the foreign supplier is retained on the safety data sheet.Importation for use in own work place — labelIf an importer imports a hazardous product from a foreign supplier for use in their own work place in Canada, the importer is exempt from the application of paragraph 3(1)(b) in respect of the requirement to provide the initial supplier identifier on the label if the name, address and telephone number of the foreign supplier is retained on the label.Repetition of symbols on labelThe sale or importation of a hazardous product is exempt from the application of paragraphs 3(1)(c) to (d), in respect of the requirement to provide a pictogram on the label of the hazardous product or its container, if the symbol of the pictogram appears on another label in accordance with the Transportation of Dangerous Goods Regulations on that same hazardous product or that same container and if the other label also meets the requirements of section 3.5.SOR/2022-272, s. 15Safety data sheet for hazardous products — same product identifierThe sale or importation of a hazardous product is exempt from the application of paragraph 13(1)(a.1) or 14(a) of the Act in respect of the requirement to provide, or cause to be provided, a safety data sheet on the sale or to obtain or prepare a safety data sheet on or before the importation, ifthe hazardous product is part of a shipment of hazardous products that have the same product identifier and a safety data sheet is obtained, prepared or provided for one of them; orthe supplier has provided to the person or government that acquires possession or ownership, or the supplier who imports the hazardous product has in their possession, a safety data sheet for a hazardous product that has the same product identifier and the safety data sheet provides, subject to section 5.12, information that is current at the time of the sale or importation.Definition of significant new dataIn this section, significant new data means new data regarding the hazard presented by a hazardous product that change its classification in a category or subcategory of a hazard class, or result in its classification in another hazard class, or change the ways to protect against the hazard presented by the hazardous product.Significant new data available within 90 days — saleThe sale of a hazardous product for which significant new data became available within 90 days prior to the sale is exempt from the application of subsection 4(1) in respect of the requirement to provide, on the safety data sheet, information that is available at the time of the sale if, at the time of the sale, the supplier ensures that the person or government that acquires possession or ownership is provided witha safety data sheet that includes all information available at the time of the sale, with the exception of the significant new data; anda document that provides the changes to the safety data sheet that are required as a result of the significant new data and the date on which the significant new data became available.Significant new data available within 90 days — importationThe importation of a hazardous product for which significant new data became available within 90 days prior to the importation is exempt from the application of subsection 4(1) in respect of the requirement to provide, on the safety data sheet, information that is available at the time of the importation if, at the time of the importation, the supplierobtains a safety data sheet that includes all of the information available at the time of the importation, with the exception of the significant new data; andobtains or prepares a document that provides the changes to the safety data sheet that are required as a result of the significant new data and the date on which the significant new data became available and appends that document to the safety data sheet referred to in paragraph (a).Significant new data available within 180 days — saleThe sale of a hazardous product for which significant new data became available within 180 days prior to the sale is exempt from the application of subsection 3(1) in respect of the requirement to provide, on the label, information elements for each category or subcategory of the hazard class in which the hazardous product is classified at the time of the sale if, at the time of the sale,the hazardous product or container in which the hazardous product is packaged has a label that provides all the information elements for each category or subcategory of the hazard class in which the hazardous product is classified at the time of the sale, with the exception of the significant new data; andthe person or government that acquires possession or ownership is provided with a document that provides the changes to the label that are required as a result of the significant new data and the date on which the significant new data became available.Significant new data available within 180 days — importationThe importation of a hazardous product for which significant new data became available within 180 days prior to the importation is exempt from the application of subsection 3(1) in respect of the requirement to provide, on the label, information elements for each category or subcategory of the hazard class in which the hazardous product is classified at the time of the importation if, at the time of the importation,the hazardous product or container in which the hazardous product is packaged has a label that includes all of the information elements for each category or subcategory of the hazard class in which the hazardous product is classified at the time of the importation, with the exception of the significant new data; andthe supplier obtains or prepares a document that provides the changes to the label that are required as a result of the significant new data and the date on which the significant new data became available.SOR/2022-272, s. 16Transfer of possession for purpose of transportationThe transfer of possession of a hazardous product that creates a bailment for the purpose of transportation or, in Quebec, the transfer of possession of a hazardous product for the purpose of transportation, without transferring ownership, and with the obligation to deliver it to the person or government that acquired possession or ownership, is exempt from the application of paragraph 13(1)(a.1) of the Act in respect of the requirement to provide, or cause to be provided, a safety data sheet to the person to whom the possession of the product is transferred for the purpose of transportation.Definition of transitIn this section, transit means, in relation to a hazardous product, its transport through Canada after being imported and before being exported, when the place of initial loading and the final destination are outside of Canada, and, while in transport, its loading, unloading, packing, unpacking or storage.Importation — transitThe importation of a hazardous product is exempt from the application of section 14 of the Act ifthe hazardous product is or is intended to be in transit; andthe hazardous product is not intended for use in a work place in Canada.Sale — exportationThe sale of a hazardous product, for the purpose of its exportation, is exempt from the application of section 13 of the Act ifthe hazardous product is or is intended to be transported or, while in transport, is or is intended to be loaded, unloaded, packed, unpacked or stored, for the purpose of that sale; andthe hazardous product is not intended for use in a work place in Canada.Importation to bring into complianceThe importation of a hazardous product is exempt from the application of paragraph 14(b) of the Act if the hazardous product is imported for the purpose of being brought into compliance with the labelling requirements of these Regulations before it is used or sold.Credible evidenceA supplier who imports a hazardous product for the purpose described in subsection (1) must, on the request of an inspector, provide credible evidence to the inspector that it is being brought into compliance with the labelling requirements of these Regulations.Additional RequirementsCommunication of information elements — health professionalsA supplier who sells or imports a hazardous product intended for use, handling or storage in a work place in Canada must provide, as soon as feasible, any information element in respect of the hazardous product that is referred to in subsection 4(1) and is in the possession of the supplier to any health professional who requests that information for the purpose of making a medical diagnosis of, or rendering medical treatment to, an individual in an emergency.ConfidentialityAny information that, by virtue of an exemption under the Hazardous Materials Information Review Act or these Regulations, is not required to be provided on the safety data sheet but has nevertheless been provided by a supplier to any health professional who requests that information for the purpose of making a medical diagnosis of, or rendering medical treatment to, an individual in a medical emergency must be kept confidential, except for the purpose for which it was provided, if the health professional has been informed by the supplier that the information is to be kept confidential.Communication of source for toxicological dataSubject to the Hazardous Materials Information Review Act, a supplier who sells or imports a hazardous product intended for use, handling or storage in a work place in Canada must disclose, as soon as feasible, the source of information for any toxicological data used in the preparation of a safety data sheet on the request of an inspector, any person or government to which the hazardous product is sold or any user of the hazardous product.SOR/2022-272, s. 17Bilingual safety data sheet and labelThe information elements provided on a safety data sheet and on a label must be in both official languages of Canada.Bilingual presentationThe information elements referred to in subsection (1) mayin the case of a safety data sheet, appear either on a single bilingual safety data sheet or in a document in two unilingual parts that constitute one bilingual safety data sheet; andin the case of a label, appear either on a single bilingual label or in a group of information elements in two unilingual parts that constitute one bilingual label.Physical Hazard ClassesExplosives[7.1 reserved]Flammable GasesDefinitionsSOR/2022-272, s. 18DefinitionsThe following definitions apply in this Subpart.chemically unstable gas means a flammable gas that is liable to react explosively even in the absence of air or oxygen. (gaz chimiquement instable)flammable gas means a gas that has a flammable range when mixed with air at 20°C and at the standard pressure of 101.3 kPa. (gaz inflammable)pyrophoric gas means a flammable gas that is liable to ignite spontaneously in air at a temperature of 54°C or less. (gaz pyrophorique)SOR/2022-272, s. 19Classification in a Category of the ClassExclusions — aerosolsAny product that is classified in a category of the hazard class “Aerosols” need not be classified in any category or subcategory of this hazard class.Exclusions — chemicals under pressureAny product that is classified in a category of the hazard class “Chemicals Under Pressure” must not be classified in any category or subcategory of this hazard class.Categories — flammable gasA flammable gas is classified in a category or subcategory of this hazard class in accordance with the following table:
TABLE
Column 1Column 2Column 3ItemCategorySubcategoryCriteria1Flammable Gases — Category 1A, Flammable GasA flammable gas thatis ignitable when mixed with air at a concentration ≤ 13.0% by volume; orhas a flammable range when mixed with air ≥ 12 percentage points, regardless of the lower flammability limit, unless data demonstrate it meets the criteria for the subcategory “Flammable Gases — Category 1B, Flammable Gas”2Flammable Gases — Category 1B, Flammable GasA flammable gas that meets the criteria for the subcategory “Flammable Gases — Category 1A, Flammable Gas”, but does not meet the criteria for the subcategory “Flammable Gases — Category 1A, Pyrophoric Gas”, “Flammable Gases — Category 1A, Chemically Unstable Gas A” or “Flammable Gases — Category 1A, Chemically Unstable Gas B”, and that hasa lower flammability limit of > 6.0% by volume in air; ora fundamental burning velocity < 10 cm/s3Flammable Gases — Category 2, Flammable GasA flammable gas that does not meet the criteria for the subcategory “Flammable Gases — Category 1A, Flammable Gas” or “Flammable Gases — Category 1B, Flammable Gas”
Subcategories — chemically unstable gasA chemically unstable gas is classified in a subcategory of this hazard class in accordance with the following table:
TABLE
Column 1Column 2ItemSubcategoryCriteria1Flammable Gases — Category 1A, Chemically Unstable Gas AA flammable gas that, at 20°C and at the standard pressure of 101.3 kPa, is a chemically unstable gas2Flammable Gases — Category 1A, Chemically Unstable Gas BA flammable gas that, at > 20°C or at a pressure > 101.3 kPa, is a chemically unstable gas
Subcategory — pyrophoric gasA pyrophoric gas is classified in the subcategory of this hazard class in accordance with the following table:
TABLE
Column 1Column 2ItemSubcategoryCriteria1Flammable Gases — Category 1A, Pyrophoric GasA flammable gas that is a pyrophoric gas
Calculation methodTest data have priority over data obtained using a calculation method. If a calculation method is used to establish whether a gas is classified in this hazard class, the calculation method set out in the International Organization for Standardization standard ISO 10156:2017 entitled Gas cylinders — Gases and gas mixtures — Determination of fire potential and oxidizing ability for the selection of cylinder valve outlets, as amended from time to time, or any other calculation method that is a scientifically validated method, must be used.Data permits classification in category or subcategoryIf the data obtained using a calculation method referred to in subsection (3) support the conclusion that the gas must be classified in a category or subcategory of this hazard class in accordance with the tables following subsection 7.2.1(2), (2.1) or (2.2), the gas must be classified in the appropriate category or subcategory.Data does not permit classification in category or subcategoryIf the data obtained using a calculation method referred to in subsection (3) support the conclusion that the gas is a flammable gas, but do not permit for the determination of classification in the appropriate category or subcategory of this hazard class, the gas must be classified in the subcategory “Flammable Gases – Category 1A, Flammable Gas”.SOR/2022-272, s. 20AerosolsSOR/2022-272, s. 21DefinitionsDefinitionsThe following definitions apply in this Subpart.flammable aerosol[Repealed, SOR/2022-272, s. 22]flammable component means a mixture or substance that is classified in a category or subcategory of a hazard class in Subpart 2, 6 or 7 of this Part. (composant inflammable)foam aerosol means the content that is dispensed from an aerosol dispenser having a spray distance of less than 15 cm and that is in the form of a foam, mousse, gel or paste. (mousse d’aérosol)spray aerosol means the content that is dispensed from an aerosol dispenser and that is not a foam aerosol. (aérosol vaporisé)SOR/2022-272, s. 22Classification in a Category of the ClassExclusionsAny product that is classified in a category of the hazard class “Chemicals Under Pressure” must not be classified in any category of this hazard class.CategoriesAn aerosol is classified in a category of this hazard class in accordance with the following table:
TABLE
Column 1Column 2ItemCategoryCriteria1Aerosols — Category 1An aerosol dispenser thatcontains ≥ 85.0% flammable components, by mass, and generates an aerosol that has a heat of combustion ≥ 30 kJ/g;generates a spray aerosol that has an ignition distance ≥ 75 cm, based on test results from the ignition distance test for spray aerosols performed in accordance with sub-section 31.4 of Part III of the Manual of Tests and Criteria; orgenerates a foam aerosol that has, based on test results from the aerosol foam flammability test performed in accordance with sub-section 31.6 of Part III of the Manual of Tests and Criteria, eithera flame height ≥ 20 cm and a flame duration ≥ 2 s, ora flame height ≥ 4 cm and a flame duration ≥ 7 s2Aerosols — Category 2An aerosol dispenser that generatesa spray aerosol that does not meet the criteria for the category “Aerosols — Category 1” and that hasa heat of combustion ≥ 20 kJ/g,an ignition distance ≥ 15 cm, based on test results from the ignition distance test for spray aerosols performed in accordance with sub-section 31.4 of Part III of the Manual of Tests and Criteria,a time equivalent ≤ 300 s/m³, based on test results from the enclosed space ignition test performed in accordance with sub-section 31.5 of Part III of the Manual of Tests and Criteria, ora deflagration density ≤ 300 g/m³, based on test results from the enclosed space ignition test performed in accordance with sub-section 31.5 of Part III of the Manual of Tests and Criteria; ora foam aerosol that does not meet the criteria for the category “Aerosols — Category 1” and that has a flame height ≥ 4 cm and a flame duration ≥ 2 s, based on test results from the aerosol foam flammability test performed in accordance with sub-section 31.6 of Part III of the Manual of Tests and Criteria3Aerosols — Category 3An aerosol dispenser thatcontains ≤ 1.0% flammable components, by mass, and generates an aerosol that has a heat of combustion <20 kJ/g;generates a spray aerosol that does not meet the criteria for the category “Aerosols — Category 1” or “Aerosols – Category 2” and that hasa time equivalent > 300 s/m³, based on test results from the enclosed space ignition test performed in accordance with sub-section 31.5 of Part III of the Manual of Tests and Criteria, ora deflagration density > 300 g/m³, based on test results from the enclosed space ignition test performed in accordance with sub-section 31.5 of Part III of the Manual of Tests and Criteria; orgenerates a foam aerosol that does not meet the criteria for the category “Aerosols – Category 1” or “Aerosols – Category 2” and that has, based on test results from the aerosol foam flammability test performed in accordance with sub-section 31.6 of Part III of the Manual of Tests and Criteria, a flame height < 4 cm or a flame duration < 2 s
Default categoryA product that contains flammable components in an aerosol dispenser for which there are no test results in accordance with subparagraph 2.1(a)(i) and referred to in subsection (2) must be classified in the category “Aerosols – Category 1”, unless the product contains flammable components at a concentration less than or equal to 1.0% and has a heat of combustion less than 20 kJ/g.SOR/2022-272, s. 23Oxidizing GasesDefinitionDefinition of oxidizing gasIn this Subpart, oxidizing gas means a gas that is liable to cause or contribute to the combustion of other material more than air does.Classification in the Category of the ClassCategoryAn oxidizing gas is classified in the category of this hazard class in accordance with the following table:
TABLE
Column 1Column 2ItemCategoryCriteria1Oxidizing Gases — Category 1A gas that has an oxidizing power > 23.5% based on one of the methods set out in the International Organization for Standardization standard ISO 10156:2017 entitled Gas cylinders — Gases and gas mixtures — Determination of fire potential and oxidizing ability for the selection of cylinder valve outlets, as amended from time to time
SOR/2022-272, s. 24Gases Under PressureDefinitionsDefinitionsThe following definitions apply in this Subpart.critical temperature means the temperature above which a pure gas cannot be liquefied, regardless of the degree of compression. (température critique)gas under pressure means a product that consists of a gas contained in a receptacle at a gauge pressure of 200 kPa or more at 20°C, or that is liquefied, or liquefied and refrigerated, but excludes any gas that has an absolute vapour pressure of not more than 300 kPa at 50°C or that is not completely gaseous at 20°C and the standard pressure of 101.3 kPa. (gaz sous pression)Classification in a Category of the ClassExclusions — aerosolsAny product that is classified in a category of the hazard class “Aerosols” need not be classified in any category of this hazard class.Exclusions — chemicals under pressureAny product that is classified in a category of the hazard class “Chemicals Under Pressure” must not be classified in any category of this hazard class.CategoriesA gas under pressure is classified in a category of this hazard class in accordance with the following table:
TABLE
Column 1Column 2ItemCategoryCriteria1Gases Under Pressure — Compressed GasA gas that when packaged under pressure is entirely gaseous at -50°C, including all gases with a critical temperature ≤ -50°C2Gases Under Pressure — Liquefied GasA gas that when packaged under pressure is partially liquid at temperatures > -50°C3Gases Under Pressure — Refrigerated Liquefied GasA gas that when packaged is partially liquid because of its low temperature4Gases Under Pressure — Dissolved GasA gas that when packaged under pressure is dissolved in a liquid phase solvent
SOR/2022-272, s. 25Flammable LiquidsDefinitionsDefinitionsThe following definitions apply in this Subpart.appropriate closed-cup method means the methods listed in paragraph 2.6.4.2.5 of the GHS, as amended from time to time. (méthode de creuset fermé appropriée)flammable liquid means a liquid that has a flash point of not more than 93°C. (liquide inflammable)Classification in a Category of the ClassExclusions — aerosolsAny product that is classified in a category of the hazard class “Aerosols” need not be classified in any category of this hazard class.Exclusions — chemicals under pressureAny product that is classified in a category of the hazard class “Chemicals Under Pressure” must not be classified in any category of this hazard class.CategoriesA flammable liquid is classified in a category of this hazard class in accordance with the following table:
TABLE
Column 1Column 2ItemCategoryCriteria1Flammable Liquids — Category 1A liquid that has a flash point < 23°C and initial boiling point ≤ 35°C2Flammable Liquids — Category 2A liquid that has a flash point < 23°C and initial boiling point > 35°C3Flammable Liquids — Category 3A liquid that has a flash point ≥ 23°C and ≤ 60°C4Flammable Liquids — Category 4A liquid that has a flash point > 60°C and ≤ 93°C
Determination of flash point — substanceIn the case of a liquid that is a substance, the flash point must be determined bytests using an appropriate closed-cup method; oruse of scientific literature that reports a value obtained from an appropriate closed-cup method.Determination of flash point — mixtureIn the case of a liquid that is a mixture, the flash point must be determined bytests using an appropriate closed-cup method; oruse of an applicable calculation method under conditions for which it has been validated according to generally accepted standards of good scientific practice at the time the validation was carried out.SOR/2022-272, s. 26Flammable SolidsDefinitionsDefinitionsThe following definitions apply in this Subpart.flammable solid means a readily combustible solid or a solid that is liable to cause or contribute to fire through friction. (solide inflammable)readily combustible solid means a powdered, granular or pasty mixture or substance that can be easily ignited by brief contact with an ignition source and, when ignited, has a flame that spreads rapidly. (solide facilement inflammable)Classification in a Category of the ClassExclusions — aerosolsAny product that is classified in a category of the hazard class “Aerosols” need not be classified in any category of this hazard class.Exclusions — chemicals under pressureAny product that is classified in a category of the hazard class “Chemicals Under Pressure” must not be classified in any category of this hazard class.CategoriesA flammable solid that is a readily combustible solid is classified in a category of this hazard class, based on results from testing performed in accordance with the burning rate test in sub-section 33.2 of Part III of the Manual of Tests and Criteria, in accordance with the following table:
TABLE
Column 1Column 2ItemCategoryCriteria1Flammable Solids — Category 1A solid that isother than a metal powder, in respect of whichthe burning time is < 45 s or the burning rate is > 2.2 mm/s, andthe wetted zone does not stop the fire or stops the fire for less than 4 min; ora metal powder, in respect of which the burning time is ≤ 5 min2Flammable Solids — Category 2A solid that isother than a metal powder, in respect of whichthe burning time is < 45 s or the burning rate is > 2.2 mm/s, andthe wetted zone stops the fire for at least 4 min; ora metal powder, in respect of which the burning time is > 5 min and ≤ 10 min
Fire through frictionA flammable solid that is a solid that is liable to cause or contribute to fire through friction is classified in the category “Flammable Solids — Category 2”.SOR/2022-272, s. 27Self-reactive Substances and MixturesDefinitionsDefinitionsThe following definitions apply in this Subpart.as packaged means packaged in the form and condition described in test series B, D, G and H of Part II of the Manual of Tests and Criteria. (tel qu’il est emballé)explosive properties means the properties of a self-reactive substance or mixture that, in laboratory testing according to test series A, C or E of Part II of the Manual of Tests and Criteria, make the substance or mixture liable to detonate, deflagrate rapidly or show a violent effect when heated under confinement. (propriétés explosives)self-reactive means, in relation to a thermally unstable liquid or solid product, mixture or substance, liable to undergo a strongly exothermic decomposition, having a heat of decomposition equal to or greater than 300 J/g, even without participation of oxygen. (autoréactif)Classification in a Category of the ClassExclusionsThe following need not be classified in any category of this hazard class:mixtures or substances, or mixtures or substances as packaged, that are classified in a category of the hazard class “Organic Peroxides”;liquid or solid mixtures that are classified in a category of the hazard class “Oxidizing Liquids” or “Oxidizing Solids”, and contain less than 5.0% of combustible organic substances; andliquid or solid substances that are classified in a category of the hazard class “Oxidizing Liquids” or “Oxidizing Solids”.CategoriesSubject to subsection (3), a self-reactive substance or mixture is classified in a category of this hazard class, based on results from testing performed in accordance with test series A to H of Part II of the Manual of Tests and Criteria, in accordance with the following table:
TABLE
Column 1Column 2ItemCategoryCriteria1Self-reactive Substances and Mixtures — Type AA liquid or solid that, as packaged, is liable to detonate, or deflagrate rapidly2Self-reactive Substances and Mixtures — Type BA liquid or solid that possesses explosive properties and, as packaged, neither detonates, nor deflagrates rapidly, but is liable to undergo a thermal explosion in that package3Self-reactive Substances and Mixtures — Type CA liquid or solid that possesses explosive properties and, as packaged, neither detonates, nor deflagrates rapidly nor undergoes a thermal explosion in that package4Self-reactive Substances and Mixtures — Type DIn laboratory testing, a liquid or solid thatdetonates partially, does not deflagrate rapidly and shows no violent effect when heated under confinement;does not detonate, deflagrates slowly and shows no violent effect when heated under confinement; orneither detonates nor deflagrates, and shows a medium effect when heated under confinement5Self-reactive Substances and Mixtures — Type EIn laboratory testing, a liquid or solid that neither detonates nor deflagrates and shows low or no effect when heated under confinement6Self-reactive Substances and Mixtures — Type FIn laboratory testing, a liquid or solid that neither detonates in the cavitated state nor deflagrates andshows low or no effect when heated under confinement, as well as low or no explosive power; orshows no effect when heated under confinement nor any explosive power, and eitherhas a SADT < 60°C when evaluated in a 50 kg package, orin the case of a liquid mixture, has a diluent that is used for desensitization with a boiling point < 150°C7Self-reactive Substances and Mixtures — Type GIn laboratory testing, a liquid or solid that neither detonates in the cavitated state nor deflagrates, shows no effect when heated under confinement nor any explosive power, and eitherhas a SADT of 60°C to 75°C when evaluated in a 50 kg package, orin the case of a liquid mixture, has a diluent that is used for desensitization with a boiling point ≥ 150°C
Exclusion after evaluationA mixture or substance with a self-accelerating decomposition temperature greater than 75°C when evaluated in a 50 kg package need not be classified in any category of this hazard class.Pyrophoric LiquidsDefinitionDefinition of pyrophoric liquidIn this Subpart, pyrophoric liquid means a liquid that is liable to ignite within five minutes after coming into contact with air.Classification in the Category of the ClassCategoryA pyrophoric liquid is classified in the category of this hazard class, based on results from testing performed in accordance with test N.3 of sub-section 33.4.5 of Part III of the Manual of Tests and Criteria, in accordance with the following table:
TABLE
Column 1Column 2ItemCategoryCriteria1Pyrophoric Liquids — Category 1A liquid that, within 5 min, eitherignites when added to an inert carrier and after coming into contact with air, orignites or chars a filter paper, after coming into contact with air
SOR/2022-272, s. 28Pyrophoric SolidsDefinitionDefinition of pyrophoric solidIn this Subpart, pyrophoric solid means a solid that is liable to ignite within five minutes after coming into contact with air.Classification in the Category of the ClassCategoryA pyrophoric solid is classified in the category of this hazard class, based on results from testing performed in accordance with test N.2 of sub-section 33.4.4 of Part III of the Manual of Tests and Criteria, in accordance with the following table:
TABLE
Column 1Column 2ItemCategoryCriteria1Pyrophoric Solids — Category 1A solid that ignites within 5 min after coming into contact with air
SOR/2022-272, s. 29Self-heating Substances and MixturesDefinitionDefinition of self-heatingIn this Subpart, self-heating means, in relation to a solid or liquid, liable to self-heat by reaction with air and without energy supply.Classification in a Category of the ClassExclusionsThe following need not be classified in any category of this hazard class:a liquid classified in the category of the hazard class “Pyrophoric Liquids”; anda solid classified in the category of the hazard class “Pyrophoric Solids”.CategoriesSubject to subsection (3), a self-heating substance or mixture is classified in a category of this hazard class, based on results from testing performed in accordance with test N.4 of sub-section 33.4.6 of Part III of the Manual of Tests and Criteria, in accordance with the following table:
TABLE
Column 1Column 2ItemCategoryCriteria1Self-heating Substances and Mixtures — Category 1A solid or liquid in respect of which a positive result is obtained in a test using a 25 mm sample cube at 140°C2Self-heating Substances and Mixtures — Category 2A solid or liquid in respect of which a positive result is obtained in a test using a 100 mm sample cube at 140°C, a negative result is obtained in a test using a 25 mm sample cube at 140°C andthe solid or liquid is packed in packages with a volume > 3 m³;a positive result is obtained in a test using a 100 mm sample cube at 120°C and the solid or liquid is packed in packages with a volume > 450 l; ora positive result is obtained in a test using a 100 mm sample cube at 100°C
Exclusion after evaluationA mixture or substance with a temperature of spontaneous combustion higher than 50°C for a volume of 27 m3 need not be classified in any category of this hazard class.SOR/2022-272, s. 30Substances and Mixtures Which, in Contact with Water, Emit Flammable GasesGeneral ProvisionInterpretationIn this Subpart, substances and mixtures which, in contact with water, emit flammable gases are liquids and solids that, by interaction with water, are liable to become spontaneously flammable or give off flammable gases in dangerous quantities, that is, in quantities that are greater than one litre of gas per kilogram of the mixture or substance per hour.SOR/2022-272, s. 31Classification in a Category of the ClassExclusionsThe following liquids or solids need not be classified in any category of this hazard class:those that have a chemical structure that does not contain metals or metalloids;those that have been shown, through accumulated experience in production or handling, not to react with water; andthose that are soluble in water to form a stable mixture.CategoriesA liquid or solid which, in contact with water, emits flammable gases is classified in a category of this hazard class, based on results from testing performed in accordance with test N.5 of sub-section 33.5.4 of Part III of the Manual of Tests and Criteria, in accordance with the following table:
TABLE
Column 1Column 2ItemCategoryCriteria1Substances and Mixtures Which, in Contact with Water, Emit Flammable Gases — Category 1A liquid or solid thatreacts with water at ambient temperature and produces a gas that is liable to ignite spontaneously;reacts with water at ambient temperature such that the rate of evolution of flammable gas is ≥ 10 l/kg of liquid or solid over any one minute; orreacts with water at ambient temperature to ignite spontaneously in any step of the test procedure2Substances and Mixtures Which, in Contact with Water, Emit Flammable Gases — Category 2A liquid or solid that reacts with water at ambient temperature such that the maximum rate of evolution of flammable gas is ≥ 20 l/kg of liquid or solid per hour3Substances and Mixtures Which, in Contact with Water, Emit Flammable Gases — Category 3A liquid or solid that reacts with water at ambient temperature such that the maximum rate of evolution of flammable gas is > 1 l/kg of liquid or solid per hour
SOR/2022-272, s. 32Oxidizing LiquidsDefinitionDefinition of oxidizing liquidIn this Subpart, oxidizing liquid means a liquid, whether or not combustible, that is liable to cause or contribute to the combustion of other material.Classification in a Category of the ClassExclusionsThe following liquids need not be classified in any category of this hazard class:any organic liquid that does not contain oxygen, fluorine or chlorine;any organic liquid that contains oxygen, fluorine or chlorine if those elements are chemically bonded only to carbon or hydrogen; andany inorganic liquid that does not contain oxygen or halogens.CategoriesAn oxidizing liquid is classified in a category of this hazard class, based on results from testing performed in accordance with test O.2 of sub-section 34.4.2 of Part III of the Manual of Tests and Criteria, in accordance with the following table:
TABLE
Column 1Column 2ItemCategoryCriteria1Oxidizing Liquids — Category 1A liquid that, when tested in a 1:1 mixture, by mass, with cellulose, spontaneously ignites, or exhibits a mean pressure rise time < the mean pressure rise time of a 1:1 mixture, by mass, of 50.0% perchloric acid and cellulose2Oxidizing Liquids — Category 2A liquid that, when tested in a 1:1 mixture, by mass, with cellulose, exhibits a mean pressure rise time ≤ the mean pressure rise time of a 1:1 mixture, by mass, of 40.0% aqueous sodium chlorate solution and cellulose3Oxidizing Liquids — Category 3A liquid that, when tested in a 1:1 mixture, by mass, with cellulose, exhibits a mean pressure rise time ≤ the mean pressure rise time of a 1:1 mixture, by mass, of 65.0% aqueous nitric acid and cellulose
Oxidizing SolidsDefinitionDefinition of oxidizing solidIn this Subpart, oxidizing solid means a solid, whether or not combustible, that is liable to cause or contribute to the combustion of other material.Classification in a Category of the ClassExclusionsThe following solids need not be classified in any category of this hazard class:any organic solid that does not contain oxygen, fluorine or chlorine;any organic solid that contains oxygen, fluorine or chlorine if those elements are chemically bonded only to carbon or hydrogen; andany inorganic solid that does not contain oxygen or halogens.CategoriesAn oxidizing solid is classified in a category of this hazard class, based on results from testing performed in accordance with test O.1 of sub-section 34.4.1 of Part III of the Manual of Tests and Criteria or test O.3 of sub-section 34.4.3 of that Part, in accordance with the following table:
TABLE
Column 1Column 2Column 3ItemCategoryCriteria Using Test O.1Criteria Using Test O.31Oxidizing Solids — Category 1A solid that, when tested in a 4:1 or 1:1 mixture, by mass, with cellulose, exhibits a mean burning time < the mean burning time of a 3:2 mixture, by mass, of potassium bromate and celluloseA solid that, when tested in a 4:1 or 1:1 mixture, by mass, with cellulose, exhibits a mean burning rate > the mean burning rate of a 3:1 mixture, by mass, of calcium peroxide and cellulose2Oxidizing Solids — Category 2A solid that, when tested in a 4:1 or 1:1 mixture, by mass, with cellulose, exhibits a mean burning time ≤ the mean burning time of a 2:3 mixture, by mass, of potassium bromate and celluloseA solid that, when tested in a 4:1 or 1:1 mixture, by mass, with cellulose, exhibits a mean burning rate ≥ the mean burning rate of a 1:1 mixture, by mass, of calcium peroxide and cellulose3Oxidizing Solids — Category 3A solid that, when tested in a 4:1 or 1:1 mixture, by mass, with cellulose, exhibits a mean burning time ≤ the mean burning time of a 3:7 mixture, by mass, of potassium bromate and celluloseA solid that, when tested in a 4:1 or 1:1 mixture, by mass, with cellulose, exhibits a mean burning rate ≥ the mean burning rate of a 1:2 mixture, by mass, of calcium peroxide and cellulose
SOR/2022-272, s. 33Organic PeroxidesDefinitionsDefinitionsThe following definitions apply in this Subpart.as packaged means packaged in the form and condition described in test series B, D, G and H of Part II of the Manual of Tests and Criteria. (tel qu’il est emballé)explosive properties means the properties of an organic peroxide that, in laboratory testing according to test series A, C or E of Part II of the Manual of Tests and Criteria, make the liquid or solid liable to detonate, deflagrate rapidly or show a violent effect when heated under confinement. (propriétés explosives)organic peroxide means an organic liquid or solid that contains the bivalent -O-O- structure. (peroxyde organique)Classification in a Category of the ClassExclusionsAn organic peroxide that contains any of the following need not be classified in any category of this hazard class:not more than 1.0% available oxygen from the organic peroxides when containing not more than 1.0% hydrogen peroxide; ornot more than 0.5% available oxygen from the organic peroxides when containing more than 1.0% but not more than 7.0% hydrogen peroxide.Available oxygen contentThe available oxygen content, in percent, of an organic peroxide mixture referred to in paragraph (1)(a) or (b) is determined by the following formula:The available oxygen content, in percent, of an organic peroxide mixture is equal to 16 times the summation, represented by the capital sigma symbol, of the series running from i to n of, opening parenthesis, the product of n, subscript i, and c, subscript i, divided by m, subscript i, closing parenthesis.whereniis the number of peroxygen groups per molecule of organic peroxide i;ciis the concentration (mass %) of organic peroxide i; andmiis the molecular mass of organic peroxide i.CategoriesAn organic peroxide is classified in a category of this hazard class, based on results from testing performed in accordance with test series A to H of Part II of the Manual of Tests and Criteria, in accordance with the following table:
TABLE
Column 1Column 2ItemCategoryCriteria1Organic Peroxides — Type AA liquid or solid that, as packaged, is liable to detonate, or deflagrate rapidly2Organic Peroxides — Type BA liquid or solid that possesses explosive properties and, as packaged, neither detonates, nor deflagrates rapidly, but is liable to undergo a thermal explosion in that package3Organic Peroxides — Type CA liquid or solid that possesses explosive properties and, as packaged, neither detonates, nor deflagrates rapidly, nor undergoes a thermal explosion in that package4Organic Peroxides — Type DIn laboratory testing, a liquid or solid thatdetonates partially, but does not deflagrate rapidly and shows no violent effect when heated under confinement;does not detonate, but deflagrates slowly and shows no violent effect when heated under confinement; orneither detonates nor deflagrates, but shows a medium effect when heated under confinement5Organic Peroxides — Type EIn laboratory testing, a liquid or solid that neither detonates nor deflagrates, and shows low or no effect when heated under confinement6Organic Peroxides — Type FIn laboratory testing, a liquid or solid that neither detonates in the cavitated state nor deflagrates andshows low or no effect when heated under confinement, as well as low or no explosive power; orshows no effect when heated under confinement nor any explosive power, and eitherhas a SADT < 60°C when evaluated in a 50 kg package, orin the case of a liquid mixture, has a diluent that is used for desensitization with a boiling point < 150°C7Organic Peroxides — Type GIn laboratory testing, a liquid or solid that neither detonates in the cavitated state nor deflagrates, shows no effect when heated under confinement nor any explosive power, and eitherhas a SADT ≥ 60°C when evaluated in a 50 kg package, orin the case of a liquid mixture, has a diluent that is used for desensitization with a boiling point ≥ 150°C
Mixtures — organic peroxidesSubject to subsection (5), a mixture of organic peroxides must be classified in the same category as the most hazardous organic peroxide in the mixture, unless data of the types referred to in subparagraph 2.1(a)(i) or (ii) or (b)(i) or (ii) are available for the mixture as a whole and the data support the conclusion that the mixture must be classified in a category that represents a less severe hazard.Mixtures — Type G organic peroxidesA mixture of two or more Type G organic peroxides must be classified in the category “Organic Peroxides — Type G”, unless the self-accelerating decomposition temperature of the mixture results in the mixture being classified in a category that represents a more severe hazard.SOR/2022-272, s. 34Corrosive to MetalsDefinitionDefinition of corrosive to metalsIn this Subpart, corrosive to metals means, in relation to a mixture or substance, liable to damage or destroy metal by chemical action.Classification in the Category of the ClassCategoryA mixture or substance that is corrosive to metals is classified in the category of this hazard class, based on results from testing performed in accordance with sub-section 37.4 of Part III of the Manual of Tests and Criteria, in accordance with the following table:
TABLE
Column 1Column 2ItemCategoryCriteria1Corrosive to Metals — Category 1A mixture or substance that has a corrosion rate on either steel or aluminium surfaces that is > 6.25 mm per year at a test temperature of 55°C
Combustible DustsDefinitionDefinition of combustible dustIn this Subpart, combustible dust means a mixture or substance that is in the form of finely divided solid particles that, upon ignition, is liable to catch fire or explode when dispersed in air.Classification in the Category of the ClassCategoryA combustible dust is classified in the category of this hazard class in accordance with the following table:
TABLE
Column 1Column 2ItemCategoryCriteria1Combustible Dusts — Category 1A mixture or substance thathas been shown to, upon ignition, catch fire or explode when dispersed in air; oris classified in a category of the hazard class “Flammable Solids” and 5.0% or more of its composition by weight is a flammable solid and has a particle size ≤ 500 µm
SOR/2022-272, s. 35Simple AsphyxiantsDefinitionDefinition of simple asphyxiantIn this Subpart, simple asphyxiant means any gas that is liable to cause asphyxiation by the displacement of air.Classification in the Category of the ClassCategoryA simple asphyxiant is classified in the category of this hazard class in accordance with the following table:
TABLE
Column 1Column 2ItemCategoryCriteria1Simple Asphyxiants — Category 1A gas that is a simple asphyxiant
[Repealed, SOR/2022-272, s. 36][Repealed, SOR/2022-272, s. 36][Repealed, SOR/2022-272, s. 36]Physical Hazards Not Otherwise ClassifiedDefinitionDefinition of physical hazard not otherwise classifiedIn this Subpart, physical hazard not otherwise classified means a physical hazard presented by a product, mixture, material or substance that is different from any other physical hazard addressed by any other Subpart in this Part and that has the characteristic of occurring by chemical reaction and resulting in the serious injury or death of a person at the time the reaction occurs.Classification in the Category of the ClassCategoryA product, mixture, material or substance is classified in the category of this hazard class in accordance with the following table:
TABLE
Column 1Column 2ItemCategoryCriteria1Physical Hazards Not Otherwise Classified — Category 1A product, mixture, material or substance that presents a physical hazard not otherwise classified
Chemicals Under PressureDefinitionDefinition of Chemicals Under PressureIn this Subpart, chemicals under pressure means liquids or solids that are packaged in a receptacle — other than an aerosol dispenser — and that are pressurized with a gas at a gauge pressure of 200 kPa or more at 20°C but excludes any gas under pressure as defined in section 7.5.SOR/2022-272, s. 37Classification in a Category of the ClassExclusionsAny product that is classified in a category of the hazard class “Aerosols” must not be classified in any category of this hazard class.CategoriesA chemical under pressure is classified in a category of this hazard class in accordance with the following table:
TABLE
Column 1Column 2ItemCategoryCriteria1Chemicals Under Pressure — Category 1A chemical under pressure that contains ≥ 85.0% flammable components, by mass, and has a heat of combustion ≥ 20 kJ/g2Chemicals Under Pressure — Category 2A chemical under pressure thatcontains > 1.0% flammable components, by mass, and has a heat of combustion < 20 kJ/g; orcontains < 85.0% flammable components, by mass, and has a heat of combustion ≥ 20 kJ/g3Chemicals Under Pressure — Category 3A chemical under pressure that contains ≤ 1.0% flammable components, by mass, and has a heat of combustion < 20 kJ/g
SOR/2022-272, s. 37Health Hazard ClassesAcute ToxicityDefinitionsDefinitionsThe following definitions apply in this Subpart.acute toxicant means a mixture or substance that is liable to cause acute toxicity, or a mixture or substance that, upon contact with water, releases a gaseous substance that is liable to cause acute toxicity. (toxique aigu)acute toxicity refers to serious adverse health effects, including death, occurring followingoral or dermal administration of a single dose of a mixture or substance, or multiple doses given within 24 hours; oran inhalation exposure to a mixture or substance of four hours or of a duration that is converted to four hours in accordance with subsection 8.1.1(4). (toxicité aiguë)dust means solid particles that are suspended in a gas, usually air. (poussières)mist means liquid droplets that are suspended in the air. (brouillard)SOR/2022-272, s. 38Classification in a Category of the ClassClassification of SubstancesLD50 or LC50 — associated rangeAn acute toxicant that is a substance is classified, with respect to each applicable route of exposure, in a category of this hazard class in accordance with the tables to subsection (3) if it has an LD50 by the oral or dermal exposure route, or an LC50 by the inhalation exposure route, that falls into one of the ranges indicated in the applicable table to that subsection.Contact with water — gaseous substanceIf an acute toxicant that is a substance is not classified in accordance with subsection (1) with respect to the inhalation route of exposure in a category of this hazard class in accordance with Table 3 to subsection (3) and, upon contact with water, the acute toxicant releases a gaseous substance that has an LC50 that falls into one of the ranges indicated in that table, it is classified in accordance with that table with regard to that range.LD50 or LC50 not availableIf an LD50 by the oral or dermal exposure route or an LC50 by the inhalation exposure route is not available, an acute toxicity point estimate must be established in accordance with the table to section 8.1.7, and the acute toxicant must be classified based on that acute toxicity point estimate, with respect to each applicable route of exposure, in a category of this hazard class in accordance with the following tables:
TABLE 1
Oral Exposure RouteColumn 1Column 2ItemCategoryRanges for LD50 or for Acute Toxicity Point Estimates (mg/kg body weight)1Acute Toxicity (Oral) — Category 1≤ 52Acute Toxicity (Oral) — Category 2> 5 and ≤ 503Acute Toxicity (Oral) — Category 3> 50 and ≤ 3004Acute Toxicity (Oral) — Category 4> 300 and ≤ 2000
TABLE 2
Dermal Exposure RouteColumn 1Column 2ItemCategoryRanges for LD50 or for Acute Toxicity Point Estimates (mg/kg body weight )1Acute Toxicity (Dermal) — Category 1≤ 502Acute Toxicity (Dermal) — Category 2> 50 and ≤ 2003Acute Toxicity (Dermal) — Category 3> 200 and ≤ 10004Acute Toxicity (Dermal) — Category 4> 1000 and ≤ 2000
TABLE 3
Inhalation Exposure RouteColumn 1Column 2Column 3Column 4Ranges for LC50 or for Acute Toxicity Point EstimatesItemCategoryGases (ppmV)Vapours (mg/l)Dusts and Mists (mg/l)1Acute Toxicity (Inhalation) — Category 1≤ 100≤ 0.5≤ 0.052Acute Toxicity (Inhalation) — Category 2> 100 and ≤ 500> 0.5 and ≤ 2> 0.05 and ≤ 0.53Acute Toxicity (Inhalation) — Category 3> 500 and ≤ 2500> 2 and ≤ 10> 0.5 and ≤ 14Acute Toxicity (Inhalation) — Category 4> 2500 and ≤ 20 000> 10 and ≤ 20> 1 and ≤ 5
One-hour exposure periodFor the purposes of Table 3 to subsection (3), the LC50 is based on a four-hour exposure period. If existing acute inhalation toxicity data have been generated according to a one-hour exposure period, the LC50 for gases and vapours must be divided by two, and the LC50 for dusts and mists must be divided by four.SOR/2022-272, s. 39Classification of MixturesOrder of provisionsThe classification of a mixture as an acute toxicant in a category of this hazard class must proceed in accordance with the order of sections 8.1.3 to 8.1.6.Concentrations for the purpose of classificationOnly ingredients present at concentrations equal to or greater than the concentration limit of 1.0% — w/w for solids, liquids, dusts, mists and vapours and v/v for gases — must be considered for the purpose of classification.Data available for mixture as a wholeIf data of the types referred to in subparagraphs 2.1(a)(i) to (iv) are available for the mixture as a whole, the mixture must be classified as an acute toxicant in accordance with section 8.1.1.Data available for use of bridging principlesIf data are available to enable the characterization of the mixture as an acute toxicant, in accordance with the bridging principles referred to in subsections 2.3(3) to (8), the mixture must be classified in a category of this hazard class in accordance with those subsections.Data available for all ingredientsIf data are available for all ingredients in the mixture, the mixture must be classified as an acute toxicant in accordance with section 8.1.1 using the ATE of the mixture that is determined in respect of each applicable route of exposure by the following formula:ATE subscript mix is equal to 100 divided by, opening square bracket, the summation, represented by the capital sigma symbol, from n, of the series capital C, subscript i, divided by ATE, subscript i, closing square bracket.whereATEmixis the ATE of the mixture determined using this formula;Ciis the concentration of ingredient i;nis the number of ingredients and i is running from 1 to n;ATEiis the ATE of ingredient i, which is eitherthe LD50 or the LC50 based on or converted to a four-hour exposure period, for i, orif the LD50 or the LC50 is unavailable, the acute toxicity point estimate established for i in accordance with the table to section 8.1.7; andiis each ingredient in the mixture withan ATE within the ranges set out in the applicable table to subsection 8.1.1(3),an oral or dermal LD50 greater than 2000 mg/kg body weight but less than or equal to 5000 mg/kg body weight, oran LC50 based on or converted to a four-hour exposure period within a range having an amplitude comparable to the one in paragraph (b).Data not available for all ingredientsIf the ATE is not available for one or more ingredients of the mixture, the mixture must be classified as an acute toxicant in accordance with section 8.1.1 using the ATE of the mixture that is determined in respect of each applicable route of exposure according to the following:if data permit the ATE to be estimated for each of those ingredients in accordance with established scientific principles, the formula in section 8.1.5 must be used;if data do not permit the ATE to be estimated for an ingredient in accordance with established scientific principles, and the concentration of the ingredient in the mixture is equal to or greater than the concentration limit of 1.0%, the mixture is classified based only on the ingredients having an ATE, such thatif the total concentration of all ingredients with unknown acute toxicity is less than or equal to 10.0% of the mixture, the formula in section 8.1.5 must be used, orif the total concentration of all ingredients with unknown acute toxicity is greater than 10.0% of the mixture, the following formula must be used:ATE subscript mix is equal to the quotient of the numerator of 100 minus, opening parenthesis, the summation, represented by the capital sigma symbol, of the series capital C, subscript unknown, if the value of C is greater than 10.0%, closing parenthesis, divided by the following denominator: opening square bracket, the summation, represented by the symbol capital sigma, from n, of the series capital C, subscript i, divided by ATE, subscript i, closing square bracket.whereATEmixis the ATE of the mixture determined using this formula,Ciis the concentration of ingredient i,Cunknownis the concentration of ingredients i with unknown ATE values,nis the number of ingredients and i is running from 1 to n,ATEiis the ATE of ingredient i, which is eitherthe LD50 or the LC50 based on or converted to a four-hour exposure period, for i, orif the LD50 or the LC50 is unavailable, the acute toxicity point estimate established for i in accordance with the table to section 8.1.7, andiis each ingredient in the mixture withan ATE within the ranges set out in the applicable table to subsection 8.1.1(3),an oral or dermal LD50 greater than 2000 mg/kg body weight but less than or equal to 5000 mg/kg body weight, oran LC50 based on or converted to a four-hour exposure period within a range having an amplitude comparable to the one in paragraph (b).Conversion from range to point estimateIf a formula in section 8.1.5 or 8.1.6 is used, an acute toxicity point estimate must be determined, in accordance with the table to subsection (2), for each ingredient for which only that ingredient’s classification category or experimentally obtained acute toxicity range is available.More than one rangeIf the experimentally obtained acute toxicity range for an ingredient does not fall entirely within any of the ranges set out in column 2 of the following table, the converted acute toxicity point estimate for that ingredient for the purposes of column 3 is the lowest value of the experimentally obtained acute toxicity range.
SOR/2022-272, s. 40Skin Corrosion/IrritationDefinitionsDefinitionsThe following definitions apply in this Subpart.skin corrosion means the production of irreversible damage to the skin, namely, visible necrosis through the epidermis and into the dermis, occurring after exposure to a mixture or substance, and includes ulcers, bleeding, bloody scabs and, within a 14-day observation period, discoloration due to blanching of the skin, complete areas of alopecia, and scars. (corrosion cutanée)skin-corrosive means, in relation to a mixture or substance, liable to cause skin corrosion. (corrosif pour la peau)skin-irritant means, in relation to a mixture or substance, liable to cause skin irritation. (irritant pour la peau)skin irritation means the production of reversible damage to the skin occurring after exposure to a mixture or substance. (irritation cutanée)SOR/2022-272, s. 41Classification in a Category or Subcategory of the ClassClassification of SubstancesOrder of provisionsThe classification of a skin-corrosive substance or a skin-irritant substance in a category or subcategory of this hazard class must proceed in accordance with the order of sections 8.2.2 to 8.2.7, unless, after applying subsections 8.2.2(1) to (3), the substance is not classified further to subsection 8.2.2(4).Human data — skin corrosionA substance for which human data demonstrate that it is a skin-corrosive substance is classified in the category “Skin Corrosion — Category 1”.Animal data — skin corrosionA substance for which purposely generated animal data demonstrate that it is a skin-corrosive substance is classified in the category “Skin Corrosion — Category 1” and is, if the applicable data are available, further classified in accordance with the following table:
TABLE
Column 1Column 2ItemSubcategoryCriteria1Skin Corrosion — Category 1AA substance that, according to animal data acquired from a scientifically validated method, produces irreversible damage to the skin after an exposure of three minutes or less, and within one hour of observation, in at least one animal2Skin Corrosion — Category 1BA substance that, according to animal data acquired from a scientifically validated method, produces irreversible damage to the skin after an exposure of more than three minutes and up to and including one hour, and within 14 days of observation, in at least one animal3Skin Corrosion — Category 1CA substance that, according to animal data acquired from a scientifically validated method, produces irreversible damage to the skin after an exposure of more than one hour and up to and including four hours, and within 14 days of observation, in at least one animal
Human or animal data — skin irritationA substance for which there are human data or purposely generated animal data with respect to skin irritation is classified in the category “Skin Irritation — Category 2” in accordance with the following table:
TABLE
Column 1Column 2ItemCategoryCriteria1Skin Irritation — Category 2A substancethat, according to human data, is skin-irritant; orin respect of which animal data revealin the case of data acquired from a test performed in accordance with the OECD Guideline for the Testing of Chemicals, No. 404, entitled Acute Dermal Irritation/Corrosion, as amended from time to time, a mean score of ≥ 2.3 and ≤ 4.0 for erythema and eschar or for edema in at least two of three animals from gradings at 24, 48 and 72 hours after patch removal or, if reactions are delayed, from gradings on three consecutive days after the onset of skin reactions,in the case of data acquired from a scientifically validated method, inflammation, namely, local alopecia, hyperkeratosis, hyperplasia and scaling, that persists to the end of the observation period specified by the method in at least two animals, orin the case of data acquired from a scientifically validated method, evidence of severe skin irritation in only one animal
No classificationA substance that meets the following conditions need not be classified in any category or subcategory of this hazard class:there are human data or purposely generated animal data on the substance, acquired from a scientifically validated method, with respect to skin corrosion or skin irritation;the substance is not classified further to subsection (1), (2) or (3); andthe data referred to in paragraph (a) demonstrate that it is neither a skin-corrosive substance nor a skin-irritant substance.SOR/2022-272, s. 42Other skin data from animalsA substance for which there are animal data on dermal exposure, acquired from a scientifically validated method, that have not been purposely generated and that demonstrate that the substance is skin-corrosive or skin-irritant is classified, respectively, in the category “Skin Corrosion — Category 1” or the category “Skin Irritation — Category 2”.In vitro or ex vivo dataA substance for which the data, in vitro or ex vivo, acquired from a scientifically validated method for the evaluation of skin corrosion or skin irritation demonstrate that the substance is skin-corrosive or skin-irritant is classified, respectively, in the category “Skin Corrosion — Category 1” or the category “Skin Irritation — Category 2”.pHA substance for which the pH is less than or equal to two or equal to or greater than 11.5 is classified in the category “Skin Corrosion — Category 1”, unless an assessment of alkali or acid reserve performed in accordance with established scientific principles supports the conclusion that it need not be classified as a skin-corrosive substance on the basis of its pH.Structure-activity relationship — skin corrosionA substance for which a structure-activity relationship, established in accordance with established scientific principles, supports the conclusion that the substance must be classified in the category “Skin Corrosion — Category 1” is classified in that category.Structure-activity relationship — skin irritationA substance for which a structure-activity relationship, established in accordance with established scientific principles, supports the conclusion that the substance must be classified in the category “Skin Irritation — Category 2” is classified in that category.Totality of available dataA substance for which an evaluation of the totality of available data, performed in accordance with established scientific principles, supports the conclusion that the substance is skin-corrosive or skin-irritant is classified, respectively, in the category “Skin Corrosion — Category 1” or the category “Skin Irritation — Category 2”.Classification of MixturesOrder of provisionsThe classification of a mixture as skin-corrosive or as skin-irritant in a category or subcategory of this hazard class must proceed in accordance with the order of sections 8.2.9 to 8.2.11.Data available for mixture as a wholeIf data of the types referred to in subparagraphs 2.1(a)(i) to (iv) are available for the mixture as a whole, the mixture must be classified in accordance with the order of sections 8.2.2 to 8.2.7, unless under subsection 8.2.2(4) the mixture need not be classified.Data available for mixture as a whole — sections 8.2.10 and 8.2.11If data of the types referred to in subparagraphs 2.1(a)(i) to (iv) are available for the mixture as a whole, but the mixture cannot be classified further to subsections 8.2.2(1) to (3) or sections 8.2.3 to 8.2.7, its classification in a category or subcategory of this hazard class must proceed in accordance with the order of sections 8.2.10 and 8.2.11.Data available for use of bridging principlesIf data are available to enable the characterization of the mixture as a skin-corrosive mixture or a skin-irritant mixture, in accordance with the bridging principles referred to in subsections 2.3(3) to (8), the mixture must be classified in a category or subcategory of this hazard class in accordance with those subsections.Data available for ingredientsSubject to subsection (3), a mixture that contains one or more ingredients that are classified in the category “Skin Corrosion — Category 1”, the subcategory “Skin Corrosion — Category 1A”, the subcategory “Skin Corrosion — Category 1B”, the subcategory “Skin Corrosion — Category 1C” or the category “Skin Irritation — Category 2” is classified in a category or subcategory of this hazard class in accordance with subsection (2), subject to the following:ingredients that are classified in the category “Skin Corrosion — Category 1”, the subcategory “Skin Corrosion — Category 1A”, the subcategory “Skin Corrosion — Category 1B”, the subcategory “Skin Corrosion — Category 1C” or the category “Skin Irritation — Category 2” and are present in the mixture at a concentration equal to or greater than the concentration limit of 1.0% must be included in the calculation of the sum of concentrations of ingredients; andingredients that are classified in the category “Skin Corrosion — Category 1”, the subcategory “Skin Corrosion — Category 1A”, the subcategory “Skin Corrosion — Category 1B”, the subcategory “Skin Corrosion — Category 1C” or the category “Skin Irritation — Category 2” and are present in the mixture at a concentration of less than the concentration limit of 1.0% must be included in the calculation of the sum of concentrations of ingredients only if there is evidence that, at the concentration at which they are present, the ingredients are skin-corrosive substances or skin-irritant substances.Classification — mixtureA mixture is classified in a category of this hazard class in accordance with the following:if the sum of concentrations of ingredients classified in the category “Skin Corrosion — Category 1” is equal to or greater than 5.0%, the mixture is classified in the category “Skin Corrosion — Category 1”;if the sum of concentrations of ingredients classified in the subcategory “Skin Corrosion — Category 1A” is equal to or greater than 5.0%, and the mixture does not contain any ingredients classified in the category “Skin Corrosion — Category 1”, the subcategory “Skin Corrosion — Category 1B”, or the subcategory “Skin Corrosion — Category 1C”, the mixture is classified in the category “Skin Corrosion — Category 1” or the subcategory “Skin Corrosion — Category 1A”;if the sum of concentrations of ingredients classified in the subcategory “Skin Corrosion — Category 1B” is equal to or greater than 5.0%, and the mixture does not contain any ingredients classified in the category “Skin Corrosion — Category 1”, the subcategory “Skin Corrosion — Category 1A”, or the subcategory “Skin Corrosion — Category 1C”, the mixture is classified in the category “Skin Corrosion — Category 1” or the subcategory “Skin Corrosion — Category 1B”;if the sum of concentrations of ingredients classified in the subcategory “Skin Corrosion — Category 1C” is equal to or greater than 5.0%, and the mixture does not contain any ingredients classified in the category “Skin Corrosion — Category 1”, the subcategory “Skin Corrosion — Category 1A”, or the subcategory “Skin Corrosion — Category 1B”, the mixture is classified in the category “Skin Corrosion — Category 1” or the subcategory “Skin Corrosion — Category 1C”;if the sum of the concentrations of ingredients set out in two or more of the following subparagraphs is equal to or greater than 5.0%, the mixture is classified in the category “Skin Corrosion ─ Category 1”:ingredients classified in the category “Skin Corrosion ─ Category 1”,ingredients classified in the subcategory “Skin Corrosion ─ Category 1A”,ingredients classified in the subcategory “Skin Corrosion ─ Category 1B”, andingredients classified in the subcategory “Skin Corrosion ─ Category 1C”;if the sum of concentrations of ingredients classified in the category “Skin Corrosion — Category 1”, ingredients classified in the subcategory “Skin Corrosion — Category 1A”, ingredients classified in the subcategory “Skin Corrosion — Category 1B” and ingredients classified in the subcategory “Skin Corrosion — Category 1C” is equal to or greater than 1.0% but less than 5.0%, the mixture is classified in the category “Skin Irritation — Category 2”;if the sum of concentrations of ingredients classified in the category “Skin Irritation — Category 2” is equal to or greater than 10.0%, the mixture is classified in the category “Skin Irritation — Category 2”; orif the sum of the results of the following subparagraphs is equal to or greater than 10.0%, the mixture is classified in the category “Skin Irritation — Category 2”:10 times the sum of concentrations of ingredients classified in the category “Skin Corrosion — Category 1”, ingredients classified in the subcategory “Skin Corrosion — Category 1A”, ingredients classified in the subcategory “Skin Corrosion — Category 1B” and ingredients classified in the subcategory “Skin Corrosion — Category 1C”, andthe sum of concentrations of ingredients classified in the category “Skin Irritation — Category 2”.Mixtures containing particular ingredientsA mixture is classified in a category of this hazard class in accordance with the following table if it contains one or more substances, such as acids, bases, inorganic salts, aldehydes, phenols or surfactants, which could be corrosive or irritant at concentrations below the concentration limits set out in subsection (2) and at least one ingredient with a concentration that is above the concentration limits set out below:
TABLE
Column 1Column 2Column 3ItemCategoryIngredientConcentration Limits1Skin Corrosion — Category 1Acid with pH ≤ 2≥ 1.0%2Skin Corrosion — Category 1Base with pH ≥ 11.5≥ 1.0%3Skin Corrosion — Category 1Other ingredients classified in the category “Skin Corrosion — Category 1”≥ 1.0%4Skin Irritation — Category 2Other ingredients classified in the category “Skin Irritation — Category 2”, including acids and bases≥ 3.0%
SOR/2022-272, s. 43Serious Eye Damage/Eye IrritationDefinitionsDefinitionsThe following definitions apply in this Subpart.eye irritation means the production of changes in the eye after exposure of the eye to a mixture or substance that are fully reversible within an observation period of 21 days after that exposure. (irritation oculaire)serious eye damage means the production of tissue damage in the eye or serious physical decay of vision, occurring after exposure of the eye to a mixture or substance,for which data demonstrate that it is irreversible; orthat is not fully reversible within an observation period of 21 days after that exposure. (lésion oculaire grave)SOR/2022-272, s. 44Classification in a Category or Subcategory of the ClassClassification of SubstancesOrder of provisionsThe classification of a substance that causes serious eye damage or eye irritation in a category or subcategory of this hazard class must proceed in accordance with the order of sections 8.3.2 to 8.3.7, unless, after applying subsections 8.3.2(1) to (4), the substance is not classified further to subsection 8.3.2(5).Human or animal data — serious eye damageA substance for which there are human data or purposely generated animal data with respect to serious eye damage is classified in the category of this hazard class in accordance with the following table:
TABLE
Column 1Column 2ItemCategoryCriteria1Serious Eye Damage — Category 1A substancethat, according to human data, causes serious eye damage;that, according to animal data acquired from a scientifically validated method from at least one animal, produces effects on the cornea, iris or conjunctivathat are irreversible as demonstrated by data, orthat are not fully reversible within an observation period of 21 days; orin respect of which animal data acquired from tests performed in accordance with the OECD Guideline for the Testing of Chemicals, No. 405, entitled Acute Eye Irritation/Corrosion, as amended from time to time, demonstrate a positive response in at least two of three animals, and the mean score calculated following gradings at 24, 48 and 72 hours after instillation of the substance, isin the case of corneal opacity, ≥ 3, orin the case of iritis, > 1.5
Human data — eye irritationA substance for which human data demonstrate that it causes eye irritation is classified in the category “Eye Irritation — Category 2”.Animal data — eye irritationA substance for which purposely generated animal data demonstrate that it causes eye irritation is classified in the category “Eye Irritation — Category 2” and is, if the applicable data are available, further classified in the appropriate subcategory in accordance with the following table:
TABLE
Column 1Column 2Column 3ItemCategorySubcategoryCriteria1Eye Irritation — Category 2Eye Irritation — Category 2AA substance that is not classified in the category “Serious Eye Damage — Category 1” and in respect of which animal data acquired from tests performed in accordance with the OECD Guideline for the Testing of Chemicals, No. 405, entitled Acute Eye Irritation/Corrosion, as amended from time to time, demonstrate in at least two of three animals a positive response that fully reverses within an observation period of more than seven days but not more than 21 days, and the mean score calculated following gradings at 24, 48 and 72 hours after instillation of the substance, isin the case of corneal opacity, ≥ 1;in the case of iritis, ≥ 1;in the case of conjunctival redness, ≥ 2; orin the case of conjunctival edema (chemosis), ≥ 22Eye Irritation — Category 2Eye Irritation — Category 2BA substance that is not classified in the category “Serious Eye Damage — Category 1” and in respect of which animal data acquired from tests performed in accordance with the OECD Guideline for the Testing of Chemicals, No. 405, entitled Acute Eye Irritation/Corrosion, as amended from time to time, demonstrate in at least two of three animals a positive response that fully reverses within an observation period of seven days, and the mean score calculated following gradings at 24, 48 and 72 hours after instillation of the substance, isin the case of corneal opacity, ≥ 1;in the case of iritis, ≥ 1;in the case of conjunctival redness, ≥ 2; orin the case of conjunctival edema (chemosis), ≥ 2
Skin corrosion dataA substance that is classified in the category “Skin Corrosion — Category 1” in accordance with subsections 8.2.2(1) and (2) is also classified in the category “Serious Eye Damage — Category 1” of this hazard class.No classificationA substance that meets the following conditions need not be classified in any category of this hazard class:the substance is not classified further to subsections (1) to (4); andhuman data or purposely generated animal data on the substance, acquired from a scientifically validated method, with respect to serious eye damage or eye irritation, demonstrate that the substance does not cause serious eye damage or eye irritation.Other animal data — eye or skin exposureA substance for which there are animal data on eye exposure that demonstrate, or animal data on skin exposure that support the conclusion, that the substance causes serious eye damage or eye irritation is classified in the category “Serious Eye Damage — Category 1” or the category “Eye Irritation — Category 2”, and, in the latter case, if the applicable data are available, the substance is further classified in the subcategory “Eye Irritation — Category 2A” or in the subcategory “Eye Irritation — Category 2B”.In vitro or ex vivo data — serious eye damageA substance for which the data, in vitro or ex vivo, acquired from a scientifically validated method for the evaluation of serious eye damage demonstrate that the substance causes serious eye damage is classified in the category “Serious Eye Damage — Category 1”.In vitro or ex vivo data — eye irritationA substance for which the data, in vitro or ex vivo, acquired from a scientifically validated method for the evaluation of eye irritation demonstrate that the substance causes eye irritation is classified in the category “Eye Irritation — Category 2” and, if the applicable data are available, the substance is further classified in the subcategory “Eye Irritation — Category 2A” or in the subcategory “Eye Irritation — Category 2B”.pHA substance for which the pH is less than or equal to two or equal to or greater than 11.5 is classified in the category “Serious Eye Damage — Category 1”, unless an assessment of alkali or acid reserve performed in accordance with established scientific principles supports the conclusion that it need not be classified as a substance that causes serious eye damage on the basis of its pH.Structure-activity relationship — serious eye damageA substance for which a structure-activity relationship, established in accordance with established scientific principles, supports the conclusion that the substance must be classified in the category “Serious Eye Damage — Category 1” is classified in that category.Structure-activity relationship — eye irritationA substance for which a structure-activity relationship, established in accordance with established scientific principles, supports the conclusion that the substance must be classified in the category “Eye Irritation — Category 2” is classified in that category and, if the applicable data are available, the substance is further classified in the subcategory “Eye Irritation — Category 2A” or in the subcategory “Eye Irritation — Category 2B”.Totality of available dataA substance for which an evaluation of the totality of available data, performed in accordance with established scientific principles, supports the conclusion that the substance causes serious eye damage or eye irritation is classified in the category “Serious Eye Damage — Category 1” or the category “Eye Irritation — Category 2” and, in the latter case, if the applicable data are available, the substance is further classified in the subcategory “Eye Irritation — Category 2A” or in the subcategory “Eye Irritation — Category 2B”.Classification of MixturesOrder of provisionsThe classification of a mixture as a mixture that causes serious eye damage or eye irritation in a category of this hazard class must proceed in accordance with the order of sections 8.3.9 to 8.3.11.Data available for mixture as a wholeIf data of the types referred to in subparagraphs 2.1(a)(i) to (iv) are available for the mixture as a whole, the mixture must be classified in accordance with the order of sections 8.3.2 to 8.3.7 unless, under subsection 8.3.2(5), the mixture need not be classified.Data available for mixture as a whole — sections 8.3.10 and 8.3.11If data of the types referred to in subparagraphs 2.1(a)(i) to (iv) are available for the mixture as a whole, but the mixture cannot be classified further to subsections 8.3.2(1) to (4) or sections 8.3.3 to 8.3.7, its classification in a category or subcategory of this hazard class must proceed in accordance with the order of sections 8.3.10 and 8.3.11.Data available for use of bridging principlesIf data are available to enable the characterization of the mixture as a mixture that causes serious eye damage or eye irritation, in accordance with the bridging principles referred to in subsections 2.3(3) to (8), the mixture must be classified in a category or subcategory of this hazard class in accordance with those subsections.Data available for ingredientsSubject to subsection (3), a mixture that contains one or more ingredients that are classified in the category “Serious Eye Damage — Category 1”, the category “Eye Irritation — Category 2”, the subcategory “Eye Irritation — Category 2A” or the subcategory “Eye Irritation — Category 2B” is classified in a category or subcategory of this hazard class in accordance with subsection (2), subject to the following:ingredients that are classified in the category “Serious Eye Damage — Category 1”, the category “Eye Irritation — Category 2”, the subcategory “Eye Irritation — Category 2A” or the subcategory “Eye Irritation — Category 2B” and are present in the mixture at a concentration equal to or greater than the concentration limit of 1.0% must be included in the calculation of the sum of concentrations of ingredients; andingredients that are classified in the category “Serious Eye Damage — Category 1”, the category “Eye Irritation — Category 2”, the subcategory “Eye Irritation — Category 2A” or the subcategory “Eye Irritation — Category 2B” and are present in the mixture at a concentration of less than the concentration limit of 1.0% must be included in the calculation of the sum of concentrations of ingredients only if there is evidence that, at the concentration at which they are present, the ingredients are substances that cause serious eye damage or eye irritation.Classification — mixtureA mixture is classified in a category of this hazard class in accordance with the following:if the sum of concentrations of ingredients classified in the category “Serious Eye Damage — Category 1”, the category “Skin Corrosion — Category 1”, the subcategory “Skin Corrosion – Category 1A”, the subcategory “Skin Corrosion – Category 1B” and the subcategory “Skin Corrosion – Category 1C” is equal to or greater than 3.0%, the mixture is classified in the category “Serious Eye Damage — Category 1”;if the sum of concentrations of ingredients classified in the category “Serious Eye Damage — Category 1”, the category “Skin Corrosion — Category 1”, the subcategory “Skin Corrosion – Category 1A”, the subcategory “Skin Corrosion – Category 1B” and the subcategory “Skin Corrosion – Category 1C” is equal to or greater than 1.0% but less than 3.0%, the mixture is classified in the category “Eye Irritation — Category 2”;if the sum of concentrations of ingredients classified in the category “Eye Irritation — Category 2” is equal to or greater than 10.0%, the mixture is classified in the category “Eye Irritation — Category 2”;if the sum of concentrations of ingredients classified in the subcategory “Eye Irritation — Category 2A” is equal to or greater than 10.0%, and the mixture does not contain any ingredients classified in the category “Eye Irritation — Category 2” or the subcategory “Eye Irritation — Category 2B”, the mixture is classified in the category “Eye Irritation — Category 2” or the subcategory “Eye Irritation — Category 2A”;if the sum of concentrations of ingredients classified in the subcategory “Eye Irritation — Category 2B” is equal to or greater than 10.0% and the mixture does not contain any ingredients classified in the category “Eye Irritation — Category 2” or the subcategory “Eye Irritation — Category 2A”, the mixture is classified in the category “Eye Irritation — Category 2” or the subcategory “Eye Irritation — Category 2B”;if the sum of the concentrations of ingredients set out in two or more of the following subparagraphs is equal to or greater than 10.0%, the mixture is classified in the category “Eye Irritation — Category 2”:ingredients classified in the category “Eye Irritation — Category 2”,ingredients classified in the subcategory “Eye Irritation — Category 2A”, andingredients classified in the subcategory “Eye Irritation — Category 2B”; orif the sum of the results of the following subparagraphs is equal to or greater than 10.0%, the mixture is classified in the category “Eye Irritation — Category 2”:10 times the total of the sum of concentrations of ingredients classified in the category “Serious Eye Damage — Category 1” and the sum of concentrations of ingredients classified in the category “Skin Corrosion — Category 1”, ingredients classified in the subcategory “Skin Corrosion — Category 1A”, ingredients classified in the subcategory “Skin Corrosion — Category 1B” and ingredients classified in the subcategory “Skin Corrosion — Category 1C”, andthe sum of concentrations of ingredients classified in the category “Eye Irritation — Category 2”, ingredients classified in the subcategory “Eye Irritation — Category 2A” and ingredients classified in the subcategory “Eye Irritation — Category 2B”.Mixtures containing particular ingredientsA mixture is classified in a category of this hazard class in accordance with the following table if the mixture contains one or more substances, such as acids, bases, inorganic salts, aldehydes, phenols or surfactants, which could cause serious eye damage or eye irritation at concentrations below the concentration limits set out in subsection (2) and at least one ingredient with a concentration that is above the concentration limits set out below:
TABLE
Column 1Column 2Column 3ItemCategoryIngredientConcentration Limits1Serious Eye Damage — Category 1Acid with pH ≤ 2≥ 1.0%2Serious Eye Damage — Category 1Base with pH ≥ 11.5≥ 1.0%3Serious Eye Damage — Category 1Other ingredients classified in the category “Serious Eye Damage — Category 1”≥ 1.0%4Eye Irritation — Category 2Other ingredients classified in the category “Eye Irritation — Category 2”, including acids and bases≥ 3.0%
SOR/2022-272, s. 45Respiratory or Skin SensitizationDefinitionsDefinitionsThe following definitions apply in this Subpart.respiratory sensitization means the production of hypersensitivity of the airways occurring after inhalation of a mixture or substance. (sensibilisation respiratoire)respiratory sensitizer means a mixture or substance that is liable to lead to hypersensitivity of the airways following inhalation. (sensibilisant respiratoire)skin sensitization means the production of an allergic response occurring after skin contact with a mixture or substance. (sensibilisation cutanée)skin sensitizer means a mixture or substance that is liable to lead to an allergic response following skin contact. (sensibilisant cutané)SOR/2022-272, s. 46Classification in a Category or Subcategory of the ClassClassification of SubstancesRespiratory sensitizer — categoryA substance that is a respiratory sensitizer is classified in the category of this hazard class in accordance with the following table:
TABLE
Column 1Column 2ItemCategoryCriteria1Respiratory Sensitizer — Category 1A substancethat, according to human data, leads to specific respiratory hypersensitivity; orin respect of which animal data acquired from scientifically validated methods for the evaluation of respiratory sensitization demonstrate positive results
Respiratory sensitizer — subcategoriesA substance classified in the category “Respiratory Sensitizer — Category 1” under subsection (1) is, if the applicable data are available, further classified in the subcategory “Respiratory Sensitizer — Category 1A” or in the subcategory “Respiratory Sensitizer — Category 1B” in accordance with the following table:
TABLE
Column 1Column 2Column 3ItemCategorySubcategoryCriteria1Respiratory Sensitizer — Category 1Respiratory Sensitizer — Category 1AA substancethat, according to human data, leads to a high frequency of occurrence of respiratory sensitization; orin respect of which animal data support the probability of a high respiratory sensitization rate in humans2Respiratory Sensitizer — Category 1Respiratory Sensitizer — Category 1BA substancethat, according to human data, leads to a low to moderate frequency of occurrence of respiratory sensitization; orin respect of which animal data support the probability of a low to moderate respiratory sensitization rate in humans
Skin sensitizer — categoryA substance that is a skin sensitizer is classified in the category of this hazard class in accordance with the following table:
TABLE
Column 1Column 2ItemCategoryCriteria1Skin Sensitizer — Category 1A substancethat, according to human data, leads to skin sensitization; orin respect of which animal data acquired from scientifically validated methods for the evaluation of skin sensitization demonstrate positive results
Skin sensitizer — subcategoriesA substance classified in the category “Skin Sensitizer — Category 1” under subsection (3) is, if the applicable data are available, further classified in the subcategory “Skin Sensitizer — Category 1A” or in the subcategory “Skin Sensitizer — Category 1B” in accordance with the following table:
TABLE
Column 1Column 2Column 3ItemCategorySubcategoryCriteria1Skin Sensitizer — Category 1Skin Sensitizer — Category 1AA substancethat, according to human data, leads to a high frequency of occurrence of skin sensitization; orin respect of which animal data acquired from scientifically validated methods for the evaluation of skin sensitization support the probability of a high skin sensitization rate in humans2Skin Sensitizer — Category 1Skin Sensitizer — Category 1BA substancethat, according to human data, leads to a low to moderate frequency of occurrence of skin sensitization; orin respect of which animal data acquired from scientifically validated methods for the evaluation of skin sensitization support the probability of a low to moderate skin sensitization rate in humans
Classification of MixturesOrder of provisionsThe classification of a mixture as a respiratory sensitizer or a skin sensitizer, or both, in one or more categories of this hazard class must proceed in accordance with the order of sections 8.4.3 to 8.4.5.Data available for mixture as a wholeIf data of the types referred to in subparagraphs 2.1(a)(i) to (iv) are available for the mixture as a whole, the mixture must be classified as a respiratory sensitizer or a skin sensitizer, or both, in accordance with section 8.4.1.Data available for use of bridging principlesIf data are available to enable the characterization of the mixture as a respiratory sensitizer or a skin sensitizer, or both, in accordance with the bridging principles referred to in subsections 2.3(3) to (8), the mixture must be classified in a category of this hazard class in accordance with those subsections.Data available for ingredientsA mixture is classified as a respiratory sensitizer or as a skin sensitizer, or both, as the case may be, in accordance with the following:as a respiratory sensitizer,in the category “Respiratory Sensitizer — Category 1”, if it contains at least one ingredient at a concentration equal to or greater than the concentration limit of 0.1% that is classified in the category “Respiratory Sensitizer — Category 1”,in the subcategory “Respiratory Sensitizer — Category 1A”, if it contains at least one ingredient at a concentration equal to or greater than the concentration limit of 0.1% that is classified in the subcategory “Respiratory Sensitizer — Category 1A”, orin the subcategory “Respiratory Sensitizer — Category 1B”, if it does not contain ingredients classified in the subcategory “Respiratory Sensitizer — Category 1A” at a concentration equal to or greater than the concentration limit of 0.1% andit contains at least one ingredient that is a solid or a liquid at a concentration equal to or greater than the concentration limit of 1.0% that is classified in the subcategory “Respiratory Sensitizer — Category 1B”, orit contains at least one ingredient that is a gas at a concentration equal to or greater than the concentration limit of 0.2% that is classified in the subcategory “Respiratory Sensitizer — Category 1B”; oras a skin sensitizer,in the category “Skin Sensitizer — Category 1”, if it contains at least one ingredient at a concentration equal to or greater than the concentration limit of 0.1% that is classified in the category “Skin Sensitizer — Category 1”,in the subcategory “Skin Sensitizer — Category 1A”, if it contains at least one ingredient at a concentration equal to or greater than the concentration limit of 0.1% that is classified in the subcategory “Skin Sensitizer — Category 1A”, orin the subcategory “Skin Sensitizer — Category 1B”, if it does not contain ingredients classified in the subcategory “Skin Sensitizer — Category 1A” at a concentration equal to or greater than the concentration limit of 0.1% and it contains at least one ingredient at a concentration equal to or greater than the concentration limit of 1.0% that is classified in the subcategory “Skin Sensitizer — Category 1B”.Germ Cell MutagenicityDefinitionsDefinitionsThe following definitions apply in this Subpart.genotoxicity means the alteration of the structure, information content or segregation of DNA by an agent or process, including those agents or processes that cause DNA damage by interfering with normal replication processes or that in a non-physiological manner temporarily alter its replication. (génotoxicité)germ cell mutagen means a mixture or substance that is liable to lead to an increased occurrence of mutations in the germ cells of a population. (mutagène des cellules germinales)germ cell mutagenicity means an increased occurrence of heritable gene mutations, including heritable structural and numerical chromosome aberrations in germ cells, occurring after exposure to a mixture or substance. (mutagénicité sur les cellules germinales)mutagenic means, in relation to a mixture or substance, liable to lead to an increased occurrence of mutations in populations of cells or organisms. (mutagène)mutagenicity means an increased occurrence of mutations in populations of cells or organisms. (mutagénicité)mutation means a permanent change in the amount or structure of the genetic material in a cell and includesthe heritable genetic changes that may be manifested at the phenotypic level; andthe underlying DNA modifications when known, including specific base pair changes and chromosomal translocations. (mutation)SOR/2022-272, s. 47Classification in a Category or Subcategory of the ClassClassification of SubstancesCategoriesA substance that is a germ cell mutagen is classified in a category or subcategory of this hazard class in accordance with the following table:
TABLE
Column 1Column 2Column 3ItemCategorySubcategoryCriteria1Germ Cell Mutagenicity — Category 1Germ Cell Mutagenicity — Category 1AA substance that, according to data from human epidemiological studies, induces heritable mutations in germ cells2Germ Cell Mutagenicity — Category 1Germ Cell Mutagenicity — Category 1BA substance in respect of whichdata acquired from in vivo heritable germ cell mutagenicity tests in mammals demonstrate positive results;data acquired from in vivo somatic cell mutagenicity tests in mammals demonstrate positive results and there is evidence that the substance has the potential to cause mutations to germ cells, such asin germ cells, positive in vivo mutagenicity test results or positive in vivo genotoxicity test results, orevidence that the substance or any of its metabolites is able to interact with the genetic material of germ cells; ordata on human germ cells demonstrate mutagenic effects, with or without demonstrating transmission to offspring, including an increase in the frequency of aneuploidy in sperm of men exposed to the substance3Germ Cell Mutagenicity — Category 2A substance in respect of whichdata acquired from in vivo somatic cell mutagenicity tests in mammals demonstrate positive results;data acquired from in vivo somatic cell genotoxicity tests demonstrate positive results and data acquired from in vitro mutagenicity tests demonstrate positive results; ordata acquired from in vitro mutagenicity tests in mammalian cells demonstrate positive results and the substance has a structure-activity relationship with germ cell mutagens classified in the subcategory “Germ Cell Mutagenicity — Category 1A”
Classification of MixturesOrder of provisionsThe classification of a mixture as a germ cell mutagen in a category or subcategory of this hazard class must proceed in accordance with the order of sections 8.5.3 to 8.5.5.Ingredient classified in Category 1 or 1AA mixture is classified in the category “Germ Cell Mutagenicity — Category 1” or the subcategory “Germ Cell Mutagenicity — Category 1A” if it contains at least one ingredient at a concentration equal to or greater than the concentration limit of 0.1% that is classified in the subcategory “Germ Cell Mutagenicity — Category 1A”, unlessthere are data for the mixture as a whole that demonstrate conclusively, based on established scientific principles, that the mixture is a germ cell mutagen, in which case the mixture is classified as a germ cell mutagen in accordance with section 8.5.1; orthe mixture as a whole has been subjected to an in vivo heritable germ cell mutagenicity test that determines that the mixture is not a germ cell mutagen, and a scientifically validated method was used and the test was performed in accordance with generally accepted standards of good scientific practice at the time it was carried out.Ingredient classified in Category 1 or 1BA mixture is classified in the category “Germ Cell Mutagenicity — Category 1” or the subcategory “Germ Cell Mutagenicity — Category 1B” if it contains at least one ingredient at a concentration equal to or greater than the concentration limit of 0.1% that is classified in the subcategory “Germ Cell Mutagenicity — Category 1B”, and does not contain any ingredient at a concentration equal to or greater than the concentration limit of 0.1% that is classified in the subcategory “Germ Cell Mutagenicity — Category 1A”, unlessthere are data for the mixture as a whole that demonstrate conclusively, based on established scientific principles, that the mixture is a germ cell mutagen, in which case the mixture is classified as a germ cell mutagen in accordance with section 8.5.1; orthe mixture as a whole has been subjected to an in vivo heritable germ cell mutagenicity test that determines that the mixture is not a germ cell mutagen, and a scientifically validated method was used and the test was performed in accordance with generally accepted standards of good scientific practice at the time it was carried out.SOR/2022-272, s. 48Ingredient classified in Category 2A mixture is classified in the category “Germ Cell Mutagenicity — Category 2” if it contains at least one ingredient at a concentration equal to or greater than the concentration limit of 1.0% that is classified in the category “Germ Cell Mutagenicity — Category 2”, unlessthere are data for the mixture as a whole that demonstrate conclusively, based on established scientific principles, that the mixture is a germ cell mutagen, in which case the mixture is classified as a germ cell mutagen in accordance with section 8.5.1; orthe mixture as a whole has been subjected to an in vivo heritable germ cell mutagenicity test that determines that the mixture is not a germ cell mutagen, and a scientifically validated method was used and the test was performed in accordance with generally accepted standards of good scientific practice at the time it was carried out.Data available for use of bridging principlesIf data are available to enable the characterization of the mixture as a germ cell mutagen, in accordance with the bridging principles referred to in subsections 2.3(3), (4) and (7), the mixture must be classified in accordance with those subsections.CarcinogenicityDefinitionsSOR/2022-272, s. 49DefinitionsThe following definitions apply in this Subpart.carcinogenic means, in relation to a mixture or substance, liable to lead to cancer or to increase the incidence of cancer. (cancérogène)carcinogenicity means the production of cancer or an increase in the incidence of cancer occurring after exposure to a mixture or substance. (cancérogénicité)SOR/2022-272, s. 50Classification in a Category or Subcategory of the ClassClassification of SubstancesCategoriesA carcinogenic substance is classified in a category or subcategory of this hazard class in accordance with the following table:
TABLE
Column 1Column 2Column 3ItemCategorySubcategoryCriteria1Carcinogenicity — Category 1Carcinogenicity — Category 1AA substance in respect of which human data establish a causal relationship between exposure to the substance and the development of cancer2Carcinogenicity — Category 1Carcinogenicity — Category 1BA substance in respect of whichhuman data establish a causal relationship between exposure to the substance and the development of cancer, but there are additional data that do not support, based on established scientific principles, the conclusion that the substance is the causative agent;animal data establish a causal relationship between exposure to the substance and an increased incidence of malignant neoplasms or a combination of benign and malignant neoplasms intwo or more species of animals, as demonstrated by one or more studies,one species of animal, as demonstrated by two or more independent studies carried out at different times, in different laboratories or under different protocols, orone species of animal, as demonstrated by a single study, if the neoplasms observed in the study are, based on established scientific principles, atypical in relation to the incidence, site, type or age at onset for the species of animal under study; orhuman data support a positive association between exposure to the substance and the development of cancer, and animal data support a positive association between exposure to the substance and an increased incidence of malignant or benign neoplasms, but the data supporting either positive association do not support a conclusion of a causal relationship, based on established scientific principles3Carcinogenicity — Category 2A substance in respect of whichhuman data support a positive association between exposure to the substance and the development of cancer, but do not support a conclusion of a causal relationship, based on established scientific principles; oranimal data support a positive association between exposure to the substance and an increased incidence of malignant or benign neoplasms, but do not support a conclusion of a causal relationship, based on established scientific principles
Classification of MixturesOrder of provisionsThe classification of a mixture as a carcinogenic mixture in a category or subcategory of this hazard class must proceed in accordance with the order of sections 8.6.3 to 8.6.5.Ingredient classified in Category 1 or 1AA mixture is classified in the category “Carcinogenicity — Category 1” or the subcategory “Carcinogenicity — Category 1A” if it contains at least one ingredient at a concentration equal to or greater than the concentration limit of 0.1% that is classified in the subcategory “Carcinogenicity — Category 1A”, unlessthere are data for the mixture as a whole that demonstrate conclusively, based on established scientific principles, that the mixture is carcinogenic, in which case the mixture is classified as a carcinogenic mixture in accordance with section 8.6.1; orthe mixture as a whole has been subjected to a carcinogenicity study that determines that the mixture is not carcinogenic, and a scientifically validated method was used and the study was performed in accordance with generally accepted standards of good scientific practice at the time it was carried out.Ingredient classified in Category 1 or 1BA mixture is classified in the category “Carcinogenicity — Category 1” or the subcategory “Carcinogenicity — Category 1B” if it contains at least one ingredient at a concentration equal to or greater than the concentration limit of 0.1% that is classified in the subcategory “Carcinogenicity — Category 1B”, and does not contain any ingredient at a concentration equal to or greater than the concentration limit of 0.1% that is classified in the subcategory “Carcinogenicity — Category 1A”, unlessthere are data for the mixture as a whole that demonstrate conclusively, based on established scientific principles, that the mixture is carcinogenic, in which case the mixture is classified as a carcinogenic mixture in accordance with section 8.6.1; orthe mixture as a whole has been subjected to a carcinogenicity study that determines that the mixture is not carcinogenic, and a scientifically validated method was used and the study was performed in accordance with generally accepted standards of good scientific practice at the time it was carried out.SOR/2022-272, s. 51Ingredient classified in Category 2A mixture is classified in the category “Carcinogenicity — Category 2” if it contains at least one ingredient at a concentration equal to or greater than the concentration limit of 0.1% that is classified in the category “Carcinogenicity — Category 2”, unlessthere are data for the mixture as a whole that demonstrate conclusively, based on established scientific principles, that the mixture is carcinogenic, in which case the mixture is classified as a carcinogenic mixture in accordance with section 8.6.1; orthe mixture as a whole has been subjected to a carcinogenicity study that determines that the mixture is not carcinogenic, and a scientifically validated method was used and the study was performed in accordance with generally accepted standards of good scientific practice at the time it was carried out.Data available for use of bridging principlesIf data are available to enable the characterization of the mixture as carcinogenic, in accordance with the bridging principles referred to in subsections 2.3(3), (4) and (7), the mixture must be classified in accordance with those subsections.Reproductive ToxicityDefinitionsDefinitionsThe following definitions apply in this Subpart.adverse effects on sexual function and fertility means any effect of a mixture or substance that is liable to interfere with sexual function or fertility, includingalterations to the female or male reproductive system;adverse effects on onset of puberty, gamete production or transport, the reproductive cycle, sexual behaviour, parturition or pregnancy outcomes;premature reproductive senescence; orany modifications to other functions that are dependent on the integrity of the reproductive system. (effets néfastes sur la fonction sexuelle et la fertilité)adverse effects on the development of the embryo, fetus or offspring means any adverse effects of a mixture or substance on the embryo, fetus or offspring, resulting from exposure of either parent to the mixture or substance prior to conception or exposure of the developing embryo or fetus to the mixture or substance during prenatal development, or of the offspring during postnatal development to the time of sexual maturation, that is manifested at any point in the development of the embryo or fetus, or that is manifested at any point in the lifespan of the offspring, and that includes the loss of the embryo or fetus, death of the developing offspring, structural abnormality, altered growth and functional deficiency. This definition excludes the induction of genetically based inheritable effects in the offspring. (effets néfastes sur le développement de l’embryon, du foetus ou de la progéniture)effects on or via lactation meansany effect of a mixture or substance that interferes with lactation; orthe presence of the mixture or substance, or its metabolites, in the maternal milk in amounts for which there is evidence that supports the conclusion, based on established scientific principles, that the health of the breast-fed child or suckling animal is liable to be threatened. (effets sur ou via l’allaitement)reproductive toxicity refers to any of the following effects occurring after exposure to a mixture or substance:adverse effects on sexual function and fertility;adverse effects on the development of the embryo, fetus or offspring; oreffects on or via lactation. (toxicité pour la reproduction)toxic to reproduction means, in relation to a mixture or substance, liable to lead to reproductive toxicity. (toxique pour la reproduction)SOR/2022-272, s. 52Classification in a Category or Subcategory of the ClassClassification of SubstancesCategories or subcategories — Categories 1A, 1B and 2A substance that is toxic to reproduction is classified in a category or subcategory of this hazard class in accordance with the following table:
TABLE
Column 1Column 2Column 3ItemCategorySubcategoryCriteria1Reproductive Toxicity — Category 1Reproductive Toxicity — Category 1AA substance in respect of which human data demonstrate that exposure to the substance leads to adverse effects on sexual function and fertility or adverse effects on the development of the embryo, fetus or offspring2Reproductive Toxicity — Category 1Reproductive Toxicity — Category 1BA substance in respect of which animal data demonstrate that exposure of the animal to the substance leads to the following:adverse effects on sexual function and fertility or adverse effects on the development of the embryo, fetus or offspring, in the absence of other toxic effects; oradverse effects on sexual function and fertility or adverse effects on the development of the embryo, fetus or offspring, in the presence of other toxic effects, provided that such adverse effects are not considered to be a secondary non-specific consequence of the other toxic effects3Reproductive Toxicity — Category 2A substance in respect of which human or animal data support a positive association between exposure to the substance and adverse effects on sexual function and fertility or adverse effects on the development of the embryo, fetus or offspring, but do not support a conclusion, based on established scientific principles, that exposure to the substance leads to such effects, provided that such effects are not considered to be a secondary non-specific consequence of other toxic effects
Category — effects on or via lactationA substance that is toxic to reproduction is classified in the category of this hazard class in accordance with the following table:
TABLE
Column 1Column 2ItemCategoryCriteria1Reproductive Toxicity — Effects on or via LactationA substance that, according to human or animal data, has effects on or via lactation
SOR/2022-272, s. 53Classification of MixturesOrder of provisionsSubject to subsection 8.7.5(2), the classification of a mixture as a mixture that is toxic to reproduction in a category or subcategory of this hazard class must proceed in accordance with the order of sections 8.7.3 to 8.7.6.Ingredient classified in Category 1 or 1AA mixture is classified in the category “Reproductive Toxicity — Category 1” or the subcategory “Reproductive Toxicity — Category 1A” if it contains at least one ingredient at a concentration equal to or greater than the concentration limit of 0.1% that is classified in the subcategory “Reproductive Toxicity — Category 1A”, unlessthere are data for the mixture as a whole that demonstrate conclusively, based on established scientific principles, that the mixture has adverse effects on sexual function and fertility or adverse effects on the development of the embryo, fetus or offspring, in which case the mixture is classified as a mixture that is toxic to reproduction in accordance with subsection 8.7.1(1); orthe mixture as a whole has been subjected to a reproductive toxicity study that determines that the mixture does not have adverse effects on sexual function and fertility or adverse effects on the development of the embryo, fetus or offspring, and a scientifically validated method was used and the study was performed in accordance with generally accepted standards of good scientific practice at the time it was carried out.Ingredient classified in Category 1 or 1BA mixture is classified in the category “Reproductive Toxicity — Category 1” or the subcategory “Reproductive Toxicity — Category 1B” if it contains at least one ingredient at a concentration equal to or greater than the concentration limit of 0.1% that is classified in the subcategory “Reproductive Toxicity — Category 1B”, and does not contain any ingredient at a concentration equal to or greater than the concentration limit of 0.1% that is classified in the subcategory “Reproductive Toxicity — Category 1A”, unlessthere are data for the mixture as a whole that demonstrate conclusively, based on established scientific principles, that the mixture has adverse effects on sexual function and fertility or adverse effects on the development of the embryo, fetus or offspring, in which case the mixture is classified as a mixture that is toxic to reproduction in accordance with subsection 8.7.1(1); orthe mixture as a whole has been subjected to a reproductive toxicity study that determines that the mixture does not have adverse effects on sexual function and fertility or adverse effects on the development of the embryo, fetus or offspring, and a scientifically validated method was used and the study was performed in accordance with generally accepted standards of good scientific practice at the time it was carried out.SOR/2022-272, s. 54Ingredient classified in Reproductive Toxicity — Category 2A mixture is classified in the category “Reproductive Toxicity — Category 2” if it contains at least one ingredient at a concentration equal to or greater than the concentration limit of 0.1% that is classified in the category “Reproductive Toxicity — Category 2”, unlessthere are data for the mixture as a whole that demonstrate conclusively, based on established scientific principles, that the mixture has adverse effects on sexual function and fertility or adverse effects on the development of the embryo, fetus or offspring, in which case the mixture is classified as a mixture that is toxic to reproduction in accordance with subsection 8.7.1(1); orthe mixture as a whole has been subjected to a reproductive toxicity study that determines that the mixture does not have adverse effects on sexual function and fertility or adverse effects on the development of the embryo, fetus or offspring, and a scientifically validated method was used and the study was performed in accordance with generally accepted standards of good scientific practice at the time it was carried out.Ingredient classified in Reproductive Toxicity — Effects on or via LactationA mixture is classified in the category “Reproductive Toxicity — Effects on or via Lactation” if it contains at least one ingredient at a concentration equal to or greater than the concentration limit of 0.1% that is classified in the category “Reproductive Toxicity — Effects on or via Lactation”, unlessthere are data for the mixture as a whole that demonstrate conclusively, based on established scientific principles, that the mixture has effects on or via lactation, in which case the mixture is classified as a mixture that is toxic to reproduction in accordance with subsection 8.7.1(2); orthe mixture as a whole has been subjected to a reproductive toxicity study that determines that the mixture does not have effects on or via lactation, and a scientifically validated method was used and the study was performed in accordance with generally accepted standards of good scientific practice at the time it was carried out.Classification in Category 1A, 1B or 2 and in Reproductive Toxicity — Effects on or via LactationDespite subsection 2.2(3), a mixture that has been classified in accordance with section 8.7.3 or 8.7.4 and meets the criteria of subsection (1) is also classified in the category “Reproductive Toxicity — Effects on or via Lactation”.Data available for use of bridging principlesIf data are available to enable the characterization of the mixture as toxic to reproduction in accordance with the bridging principles referred to in subsections 2.3(3), (4) and (7), the mixture must be classified in accordance with those subsections, in the following categories:“Reproductive Toxicity — Category 1”;“Reproductive Toxicity — Category 2”;“Reproductive Toxicity — Effects on or via Lactation”;both “Reproductive Toxicity — Category 1” and “Reproductive Toxicity — Effects on or via Lactation”; orboth “Reproductive Toxicity — Category 2” and “Reproductive Toxicity — Effects on or via Lactation”.Specific Target Organ Toxicity — Single ExposureDefinitionsDefinitionsThe following definitions apply in this Subpart.narcotic effects means central nervous system depression thatin humans, may present as drowsiness, narcosis, reduced alertness, loss of reflexes, lack of coordination, vertigo, severe headache or nausea and may lead to reduced judgment, dizziness, irritability, fatigue, impaired memory function, deficits in perception or coordination, prolonged reaction time or sleepiness; andin animals, may be observed as lethargy, lack of coordination righting reflex, narcosis or ataxia. (effets narcotiques)organ includes any biological system. (organe)respiratory tract irritation means localized redness, edema, pruritis or irritant effects in the respiratory tract that impair its function, whether or not accompanied by cough, pain, choking, breathing difficulties or other respiratory symptoms. (irritation des voies respiratoires)specific target organ toxicity arising from a single exposure means specific, non-lethal toxic effects on target organs that arise from a single exposure to a mixture or substance, including all health effects liable to impair function of the body or any of its parts, whether reversible or irreversible, immediate or delayed, but excludes effects resulting from health hazards addressed by Subparts 1 to 7 and 10 of this Part. (toxicité pour certains organes cibles à la suite d’une exposition unique)Classification in a Category of the ClassClassification of SubstancesTwo evaluationsIn order to establish the classification of a substance that causes specific target organ toxicity arising from a single exposure in one or more categories of this hazard class, the substance must be evaluated in accordance with all the criteria set out in column 2 of the following table, in relation to toxic effects onthe central nervous system and respiratory tract; andother specific target organs.
TABLE
Column 1Column 2ItemCategoryCriteria1Specific Target Organ Toxicity — Single Exposure — Category 1A substance thataccording to human data, causes specific target organ toxicity arising from a single exposure; oraccording to animal data, causes specific target organ toxicity arising from a single exposure at low exposure concentrations, within the concentration value ranges set out for Category 1 in Table 3.8.1 of the GHS2Specific Target Organ Toxicity — Single Exposure — Category 2A substance that, according to animal data, causes specific target organ toxicity arising from a single exposure at moderate exposure concentrations, within the concentration value ranges set out for Category 2 in Table 3.8.1 of the GHS3Specific Target Organ Toxicity — Single Exposure — Category 3A substance in respect of which data demonstrate that a single exposure to the substance generates transient narcotic effects or transient respiratory tract irritation
ClassificationFollowing the evaluations referred to in subsection (1), the substance is classified in one or more categories of this hazard class, based on the results of the evaluations of its toxic effects as set out in columns 1 and 2 of the following table, in accordance with the corresponding category set out in column 3:
TABLE
Column 1Column 2Column 3Item Number of the Table to Subsection (1) that is Associated with the Criteria in Column 2 of that Table that are Determined to Have Been Met as a Result of the Evaluation of the Following:ClassificationItemToxic Effects on the Central Nervous System and Respiratory TractToxic Effects on Other Specific Target OrgansCategory of the “Specific Target Organ Toxicity — Single Exposure” Hazard Class1NoneItem 1Category 12Item 1NoneCategory 13Item 1Item 1Category 14NoneItem 2Category 25Item 2NoneCategory 26Item 1Item 2Category 17Item 2Item 1Category 18Item 2Item 2Category 29Item 3NoneCategory 310Item 3Item 1Category 1 and Category 311Item 3Item 2Category 2 and Category 3
Classification of MixturesOrder of provisionsThe classification of a mixture as a mixture that causes specific target organ toxicity arising from a single exposure in a category of this hazard class must proceed in accordance with the order of sections 8.8.3 to 8.8.5.Data available for mixture as a wholeIf data of the types referred to in subparagraphs 2.1(a)(i) to (iv) are available for the mixture as a whole, the mixture must be classified as a mixture that causes specific target organ toxicity arising from a single exposure in accordance with section 8.8.1.Data available for use of bridging principlesIf data are available to enable the characterization of the mixture as a mixture that causes specific target organ toxicity arising from a single exposure, in accordance with the bridging principles referred to in subsections 2.3(3) to (8), the mixture must be classified in one or more categories of this hazard class, based on the table to subsection 8.8.1(2), in accordance with those subsections.Data available for ingredients — Category 1, 2 or 3A mixture that contains one or more ingredients that are classified as a substance that causes specific target organ toxicity arising from a single exposure is classified as follows:in the category “Specific Target Organ Toxicity — Single Exposure — Category 1”, if it contains at least one ingredient at a concentration equal to or greater than the concentration limit of 1.0% that is classified in the category “Specific Target Organ Toxicity — Single Exposure — Category 1”;in the category “Specific Target Organ Toxicity — Single Exposure — Category 2”, if it contains at least one ingredient at a concentration equal to or greater than the concentration limit of 1.0% that is classified in the category “Specific Target Organ Toxicity — Single Exposure — Category 2”;in the category “Specific Target Organ Toxicity — Single Exposure — Category 3”, if it contains at least one ingredient that is classified in the category “Specific Target Organ Toxicity — Single Exposure — Category 3” that isat a concentration equal to or greater than the concentration at which the effect is elicited, if known, orat a concentration equal to or greater than the concentration limit of 20.0%; or[Repealed, SOR/2022-272, s. 55]in the category “Specific Target Organ Toxicity — Single Exposure — Category 3”, if it contains at least two ingredients that are classified in that category which are present individually at a concentration of 1.0% or more andsuch ingredients individually cause a transient narcotic effect, and the sum of their concentrations is equal to or greater than the concentration limit of 20.0%, orsuch ingredients individually cause transient respiratory tract irritation, and the sum of their concentrations is equal to or greater than the concentration limit of 20.0%.Data available for ingredients — Categories 1 and 3 or 2 and 3Despite subsection 2.2(3), a mixture that has been classified in accordance with paragraph (1)(a) or (b) and meets the criteria of paragraph (1)(c) is also classified in the category “Specific Target Organ Toxicity — Single Exposure — Category 3”.SOR/2022-272, s. 55Specific Target Organ Toxicity — Repeated ExposureDefinitionsDefinitionsThe following definitions apply in this Subpart.organ includes any biological system. (organe)specific target organ toxicity arising from repeated exposure means specific toxic effects on target organs that arise from repeated exposure to a mixture or substance, including all health effects liable to impair function of the body or any of its parts, whether reversible or irreversible, immediate or delayed, but excludes effects resulting from health hazards addressed by Subparts 1 to 7 and 10 of this Part. (toxicité pour certains organes cibles à la suite d’expositions répétées)Classification in a Category of the ClassClassification of SubstancesCategoriesA substance that causes specific target organ toxicity arising from repeated exposure is classified in a category of this hazard class in accordance with the following table:
TABLE
Column 1Column 2ItemCategoryCriteria1Specific Target Organ Toxicity — Repeated Exposure — Category 1A substance thataccording to human data, causes specific target organ toxicity arising from repeated exposure; oraccording to animal data, causes specific target organ toxicity arising from repeated exposure at low exposure concentrations, within the concentration value ranges set out in Table 3.9.1 of the GHS2Specific Target Organ Toxicity — Repeated Exposure — Category 2A substance that, according to animal data, causes specific target organ toxicity arising from repeated exposure at moderate exposure concentrations, within the concentration value ranges set out in Table 3.9.2 of the GHS
Classification of MixturesOrder of provisionsThe classification of a mixture as a mixture that causes specific target organ toxicity arising from repeated exposure in a category of this hazard class must proceed in accordance with the order of sections 8.9.3 to 8.9.5.Data available for mixture as a wholeIf data of the types referred to in subparagraphs 2.1(a)(i) to (iv) are available for the mixture as a whole, the mixture must be classified as a mixture that causes specific target organ toxicity arising from repeated exposure in accordance with section 8.9.1.Data available for use of bridging principlesIf data are available to enable the characterization of the mixture as a mixture that causes specific target organ toxicity arising from repeated exposure, in accordance with the bridging principles referred to in subsections 2.3(3) to (8), the mixture must be classified in a category of this hazard class in accordance with those subsections.Data available for ingredientsA mixture that contains one or more ingredients that are classified as a substance that causes specific target organ toxicity arising from repeated exposure is classified as follows:in the category “Specific Target Organ Toxicity — Repeated Exposure — Category 1”, if it contains at least one ingredient at a concentration equal to or greater than the concentration limit of 1.0% that is classified in the category “Specific Target Organ Toxicity — Repeated Exposure — Category 1”; orin the category “Specific Target Organ Toxicity — Repeated Exposure — Category 2”, if it contains at least one ingredient at a concentration equal to or greater than the concentration limit of 1.0% that is classified in the category “Specific Target Organ Toxicity — Repeated Exposure — Category 2”.Aspiration HazardDefinitionsDefinitionsThe following definitions apply in this Subpart.aspiration toxicant means a mixture or substance that is liable to cause aspiration toxicity. (toxique par aspiration)aspiration toxicity includes severe acute effects, such as chemical pneumonia, varying degrees of pulmonary injury or death, following the entry of a liquid or solid directly through the oral or nasal cavity, or indirectly from vomiting, into the trachea and lower respiratory system. (toxicité par aspiration)Classification in the Category of the ClassClassification of SubstancesCategoryA substance that is an aspiration toxicant is classified in the category of this hazard class in accordance with the following table:
TABLE
Column 1Column 2ItemCategoryCriteria1Aspiration Hazard — Category 1A substance thataccording to human data, produces aspiration toxicity if aspirated; orin the case of a liquid hydrocarbon, has a kinematic viscosity ≤ 20.5 mm2/s, measured at 40°C
Classification of MixturesOrder of provisionsThe classification of a mixture as an aspiration toxicant in the category of this hazard class must proceed in accordance with the order of sections 8.10.3 to 8.10.5.Data available for mixture as a wholeIf data of the types referred to in subparagraphs 2.1(a)(i) to (iv) are available for the mixture as a whole, the mixture must be classified as an aspiration toxicant in accordance with section 8.10.1.Data available for use of bridging principlesIf data are available to enable the characterization of the mixture as an aspiration toxicant, in accordance with the bridging principles referred to in subsections 2.3(3) to (7), the mixture must be classified in accordance with those subsections. However, subsection 2.3(3) does not apply if the concentration of aspiration toxicant in the mixture is less than the concentration limit of 10.0%.Data available for ingredientsA mixture that contains one or more ingredients that are classified as an aspiration toxicant is classified in the category “Aspiration Hazard — Category 1” ifthe sum of the concentrations of the ingredients that are present individually at a concentration of 1.0% or more and that are classified in the category “Aspiration Hazard — Category 1” is equal to or greater than the concentration limit of 10.0% and the mixture has a kinematic viscosity less than or equal to 20.5 mm2/s, measured at 40°C; orit separates into two or more distinct layers, in one of which the sum of the concentrations of the ingredients that are present individually at a concentration of 1.0% or more and that are classified in the category “Aspiration Hazard — Category 1” is equal to or greater than the concentration limit of 10.0% and the kinematic viscosity of this layer, measured at 40°C, is less than or equal to 20.5 mm2/s.Biohazardous Infectious MaterialsDefinitionDefinition of biohazardous infectious materialIn this Subpart, biohazardous infectious material means any microorganism, nucleic acid or protein that causes or is a probable cause of infection, with or without toxicity, in humans or animals.Classification in the Category of the ClassClassification of SubstancesCategoryA substance that is a biohazardous infectious material is classified in the category of this hazard class in accordance with the following table:
TABLE
Column 1Column 2ItemCategoryCriteria1Biohazardous Infectious Materials — Category 1A biohazardous infectious material thatfalls into Risk Group 2, Risk Group 3 or Risk Group 4, as defined in subsection 3(1) of the Human Pathogens and Toxins Act; orhas been shown to be a cause or probable cause of infection or infection and toxicity in animals
Classification of MixturesMixture containing more than one biohazardous infectious materialA mixture that contains one or more ingredients that are classified as a biohazardous infectious material must be classified in accordance with section 8.11.1.Health Hazards Not Otherwise ClassifiedDefinitionDefinition of health hazard not otherwise classifiedIn this Subpart, health hazard not otherwise classified means a health hazard presented by a mixture or substance that is different from any other health hazard addressed by any other Subpart in this Part and that has the characteristic of occurring via acute or repeated exposure and having an adverse effect on the health of a person exposed to it, including an injury, or resulting in the death of that person.Classification in the Category of the ClassClassification of SubstancesCategoryA substance that presents a health hazard not otherwise classified is classified in the category of this hazard class in accordance with the following table:
TABLE
Column 1Column 2ItemCategoryCriteria1Health Hazards Not Otherwise Classified — Category 1A substance that presents a health hazard not otherwise classified
Classification of MixturesOrder of provisionsThe classification of a mixture as a health hazard not otherwise classified in the category of this hazard class must proceed in accordance with the order of sections 8.12.3 and 8.12.4.Data available for mixture as a wholeIf data of the types referred to in subparagraphs 2.1(a)(i) to (iv) are available for the mixture as a whole, the mixture must be classified as a health hazard not otherwise classified in accordance with section 8.12.1.Data available for ingredientsA mixture that contains one or more ingredients that are classified as a health hazard not otherwise classified at a concentration equal to or greater than the concentration limit of 1.0% is classified in the category “Health Hazards Not Otherwise Classified — Category 1”.Consequential Amendments, Transitional Provisions, Repeals and Coming into ForceConsequential AmendmentsFood and Drug Regulations[Amendment]Hazardous Materials Information Review Regulations[Amendments][Amendment][Amendment][Amendment]Hazardous Materials Information Review Act Appeal Board Procedures Regulations[Amendments][Amendments][Amendment]Consumer Chemicals and Containers Regulations, 2001[Amendment]Safety of Human Cells, Tissues and Organs for Transplantation Regulations[Amendment]Transitional ProvisionsDefinitionsThe following definitions apply in this section.controlled product has the same meaning as in section 2 of the Hazardous Products Act as it read immediately before the day on which subsection 111(1) of the Economic Action Plan 2014 Act, No. 1 comes into force. (produit contrôlé)former Regulations means the Controlled Products Regulations and the Ingredient Disclosure List as they each read immediately before the day on which these Regulations come into force. (règlements antérieurs)Compliance — supplierThese Regulations do not apply to a supplier in respect of the sale or importation of a controlled product that is a hazardous product, as defined in section 2 of the Hazardous Products Act as enacted by subsection 111(3) of the Economic Action Plan 2014 Act, No. 1, if the supplier sells or imports the controlled product on or after the first day on which both sections 114 and 115 of the Economic Action Plan 2014 Act, No. 1 are in force, but before a day to be fixed by order of the Governor in Council for the purposes of sections 130, 133 and 135 of the Economic Action Plan 2014 Act, No. 1, and if the supplier would not, were the former Regulations in force at the time, be in contravention of the former Regulations.Hazardous product that is not controlled productThese Regulations do not apply to a supplier in respect of the sale or importation of a hazardous product, as defined in section 2 of the Hazardous Products Act as enacted by subsection 111(3) of the Economic Action Plan 2014 Act, No. 1, that is not a controlled product, if the supplier sells or imports the hazardous product on or after the first day on which both sections 114 and 115 of the Economic Action Plan 2014 Act, No. 1 are in force, but before a day to be fixed by order of the Governor in Council for the purposes of section 130 of the Economic Action Plan 2014 Act, No. 1.Compliance — supplierThese Regulations do not apply to a supplier to whom a controlled product that is a hazardous product, as defined in section 2 of the Hazardous Products Act as enacted by subsection 111(3) of the Economic Action Plan 2014 Act, No. 1, was sold if the supplier sells the controlled product on or after the first day on which both sections 114 and 115 of the Economic Action Plan 2014 Act, No. 1 are in force, but before a day to be fixed by order of the Governor in Council for the purposes of sections 131, 134 and 136 of the Economic Action Plan 2014 Act, No. 1, and if the supplier would not, were the former Regulations in force at the time, be in contravention of the former Regulations.Hazardous product that is not controlled productThese Regulations do not apply to a supplier to whom a hazardous product, as defined in section 2 of the Hazardous Products Act as enacted by subsection 111(3) of the Economic Action Plan 2014 Act, No. 1, that is not a controlled product, was sold if the supplier sells the hazardous product on or after the first day on which both sections 114 and 115 of the Economic Action Plan 2014 Act, No. 1 are in force, but before a day to be fixed by order of the Governor in Council for the purposes of section 131 of the Economic Action Plan 2014 Act, No. 1.Compliance — importation — own use in work placeThese Regulations do not apply to a supplier in respect of the importation of a controlled product that is a hazardous product, as defined in section 2 of the Hazardous Products Act as enacted by subsection 111(3) of the Economic Action Plan 2014 Act, No. 1, if the supplier imports the controlled product only for use in their work place on or after the first day on which both sections 114 and 115 of the Economic Action Plan 2014 Act, No. 1 are in force, but before a day to be fixed by order of the Governor in Council for the purposes of sections 132, 134 and 137 of the Economic Action Plan 2014 Act, No. 1, and if the supplier would not, were the former Regulations in force at the time, be in contravention of the former Regulations.Hazardous product that is not controlled productThese Regulations do not apply to a supplier in respect of the importation of a hazardous product, as defined in section 2 of the Hazardous Products Act as enacted by subsection 111(3) of the Economic Action Plan 2014 Act, No. 1, that is not a controlled product, if the supplier imports the hazardous product only for use in their work place on or after the first day on which both sections 114 and 115 of the Economic Action Plan 2014 Act, No. 1 are in force, but before a day to be fixed by order of the Governor in Council for the purposes of section 132 of the Economic Action Plan 2014 Act, No. 1.Repeals[Repeal][Repeal]Coming into ForceS.C. 2014, c. 20These Regulations come into force on the first day on which sections 114, 115 and 120 of the Economic Action Plan 2014 Act, No. 1 are all in force, but if they are registered after that day, they come into force on the day on which they are registered.[Note: Regulations in force February 11, 2015, see SI/2015-5.](Paragraphs 4(1)(a) and (b), subsection 4(2), paragraph 4.1(1)(b) and subsections 5(6), 5.6(2) and (3), 5.7(5) to (10), 5.8(1) and 5.9(1))
Information Elements on Safety Data SheetColumn 1Column 2ItemHeadingSpecific Information Elements1Identificationproduct identifier;other means of identification;recommended use and restrictions on use;initial supplier identifier; andemergency telephone number and any restrictions on the use of that number, if applicable2Hazard identificationclassification of the hazardous product, namely, the appropriate category or subcategory of the hazard class identified in Subparts 2 to 18 and 21 of Part 7 or Subparts 1 to 11 of Part 8, or a name that is its substantive equivalent, or for Subpart 20 of Part 7 and Subpart 12 of Part 8, the category of the hazard class or a description of the identified hazard;subject to subsections 3(2) and (4) to (5) of these Regulations, for each category or subcategory in which the hazardous product is classified, with the exception of the categories referred to in paragraphs (b.1) to (b.3), the information elements, namely, the symbol, signal word, hazard statement and precautionary statement, that are specified for that category or subcategory in section 3 of Annex 3 of the GHS. If the required information element is a symbol, either the name of the symbol or the symbol itself may be used;subject to subsection 3(2) of these Regulations, in the case of a hazardous product that is classified in the category “Chemicals Under Pressure – Category 1” or “Chemicals Under Pressure – Category 2”, the symbol, signal word, hazard statement and precautionary statement that are specified for that category in section 3 of Annex 3 of the United Nations document entitled Globally Harmonized System of Classification and Labelling of Chemicals (GHS), Eighth Revised Edition. Either the name of the symbol or the symbol itself may be used;subject to subsection 3(2) of these Regulations, in the case of a hazardous product that is classified in the category “Chemicals Under Pressure – Category 3”, the symbol, signal word and precautionary statement that are specified for that category in section 3 of Annex 3 of the United Nations document entitled Globally Harmonized System of Classification and Labelling of Chemicals (GHS), Eighth Revised Edition, as well as the hazard statement “Chemical under pressure: May explode if heated/Produit chimique sous pression : peut exploser sous l’effet de la chaleur”. Either the name of the symbol or the symbol itself may be used;subject to subsection 3(2) of these Regulations, for each category set out in Subparts 17, 18 and 20 of Part 7 and in Subparts 11 and 12 of Part 8 in which the hazardous product is classified,the information elements that are specified for that category in Schedule 5 (if the required information element is a symbol, either the name of the symbol or the symbol itself may be used), andany precautionary statements that are applicable to the hazardous product in terms ofgeneral precautionary statements,prevention precautionary statements,response precautionary statements,storage precautionary statements, anddisposal precautionary statements;the information elements referred to in paragraphs 3(1)(e) to (g) of these Regulations; andother hazards known to the supplier with respect to the hazardous product3Composition/Information on ingredientsIn the case of a hazardous product that is a material or substance,its chemical name;its common name and synonyms;its CAS registry number and any unique identifiers; andthe chemical name of the impurities, stabilizing solvents and stabilizing additives that are known to the supplier, that individually are classified in any category or subcategory of a health hazard class and that contribute to the classification of the material or substanceIn the case of a hazardous product that is a mixture, for each material or substance in the mixture that, individually, is classified in any category or subcategory of a health hazard class and is present above the concentration limit that is designated for the category or subcategory in which it is classified — regardless of whether the material or substance contributes to the classification of the mixture as a hazardous product — or is present in the mixture at a concentration that results in the mixture being classified in a category or subcategory of any health hazard class,its chemical name;its common name and synonyms;its CAS registry number and any unique identifiers; andits concentration4First-aid measuresa description of necessary first-aid measures, subdivided according to the different routes of exposure (inhalation, ingestion, skin and eye contact);the most important symptoms and effects, whether acute or delayed; andan indication of immediate medical attention and special treatment needed, if necessary5Fire-fighting measuressuitable and unsuitable extinguishing media;specific hazards arising from the hazardous product, such as the nature of any hazardous combustion products; andspecial protective equipment and precautions for fire-fighters6Accidental release measurespersonal precautions, protective equipment and emergency procedures; andmethods and materials for containment and cleaning up7Handling and storageprecautions for safe handling; andconditions for safe storage, including any incompatibilities8Exposure controls/Personal protectioncontrol parameters, including occupational exposure limit values or biological limit values and the source of those values;appropriate engineering controls; andindividual protection measures, such as personal protective equipment9Physical and chemical propertiesphysical state;colour;odour;melting point and freezing point;boiling point or initial boiling point and boiling range;flammability;lower and upper explosion limit or lower and upper flammability limit;flash point;auto-ignition temperature;decomposition temperature;pH;kinematic viscosity;solubility;partition coefficient — n-octanol/water (logarithmic value);vapour pressure;density and relative density;relative vapour density; andparticle characteristics10Stability and reactivityreactivity;chemical stability;possibility of hazardous reactions;conditions to avoid, including static discharge, shock or vibration;incompatible materials; andhazardous decomposition products11Toxicological informationConcise but complete description of the various toxic health effects and the data used to identify those effects, includinginformation on the likely routes of exposure (inhalation, ingestion, skin and eye contact);symptoms related to the physical, chemical and toxicological characteristics;delayed and immediate effects, and chronic effects from short-term and long-term exposure; andnumerical measures of toxicity, including ATEs12Ecological informationecotoxicity (aquatic and terrestrial, if available);persistence and degradability;bioaccumulative potential;mobility in soil; andother adverse effects13Disposal considerationsInformation on safe handling for disposal and methods of disposal, including any contaminated packaging14Transport informationUN number;United Nations proper shipping name as provided for in the United Nations Model Regulations;transport hazard class as provided in the United Nations Model Regulations;packing group as provided in the United Nations Model Regulations;environmental hazards according to the International Maritime Dangerous Goods Code and the United Nations Model Regulations; and[Repealed, SOR/2022-272, s. 59]special precautions in connection with transport or conveyance either within or outside the premises15Regulatory informationSafety, health and environmental regulations, made within or outside Canada, specific to the product in question16Other informationDate of the latest revision of the safety data sheet
SOR/2022-272, s. 56SOR/2022-272, s. 57SOR/2022-272, s. 58SOR/2022-272, s. 59(Subsection 4(3))
Information Elements on Safety Data Sheet — Biohazardous Infectious MaterialsColumn 1Column 2ItemHeadingSpecific Information Elements1Section I — Infectious Agentname;synonym or cross-reference; andcharacteristics2Section II — Hazard Identificationpathogenicity/toxicity;epidemiology;host range;infectious dose;mode of transmission;incubation period; andcommunicability3Section III — Disseminationreservoir;zoonosis; andvectors4Section IV — Stability and Viabilitydrug susceptibility/resistance;susceptibility to disinfectants;physical inactivation; andsurvival outside host5Section V — First Aid/Medicalsurveillance;first aid/treatment;immunization; andprophylaxis6Section VI — Laboratory Hazardlaboratory-acquired infections;sources/specimens;primary hazards; andspecial hazards7Section VII — Exposure Controls/Personal Protectionrisk group classification;containment requirements;protective clothing; andother precautions8Section VIII — Handling and Storagespills;disposal; andstorage9Section IX — Regulatory and Other Informationregulatory information;last file update (date); andprepared by (name of author)
(Subsections 3(3) and (3.1), section 3.1, paragraph 5.3(c) and Schedule 5)
Symbols and PictogramsColumn 1Column 2Column 3ItemName of SymbolSymbolPictogram1FlameThe image of a flame with a thick black edge and the middle of the image, also in the shape of a flame, is white. This image rests above a horizontal black line of the same width as the black contour of the flame. This symbol is used to warn about the presence of a flammability hazard.A red square, set on one of its points, outlined on a white background, symbolizing danger. It contains, inside its perimeter, the image of a flame with a thick black edge and the middle of the image, also in the shape of a flame, is white. This image rests above a horizontal black line of the same width as the black contour of the flame. This pictogram is used to warn about the presence of a flammability hazard.2Flame over circleThe image of a black flame with, at its base, five little white flames. This image rests along the contour of the upper half of a black ring with a white centre, the bottom of which rests on a horizontal black line of the same width as the ring diameter. This symbol is used to warn about the presence of an oxidizing hazard.A red square, set on one of its points, outlined on a white background, symbolizing danger. It contains, inside its perimeter, the image of a black flame with, at its base, five little white flames. This image rests along the contour of the upper half of a black ring with a white centre, the bottom of which rests on a horizontal black line of the same width as the ring diameter. This pictogram is used to warn about the presence of an oxidizing hazard.3Exploding bombThe image of a fragmenting solid black circle projecting debris in all directions. This symbol is used to warn about the presence of an explosion hazard.A red square, set on one of its points, outlined on a white background, symbolizing danger. It contains, inside its perimeter, the image of a fragmenting solid black circle projecting debris in all directions. This pictogram is used to warn about the presence of an explosion hazard.4CorrosionTwo images side by side. On the right side is a test tube pouring black droplets toward the right onto a hand whose fingers are directed toward the left, and causing damage at the point of contact. On the left side is another test tube pouring black droplets toward the left onto a black rectangle and causing damage at the point of contact. Both images include four vertical wavy lines that radiate from the point of contact to symbolize smoke or fumes. The images of the test tubes have a black outline and white background and include the images of a black liquid near their pour points. This symbol is used to warn about the presence of a corrosive hazard.A red square, set on one of its points, outlined on a white background, symbolizing danger. It contains, inside its perimeter, two images side by side. On the right side is a test tube pouring black droplets toward the right onto a hand whose fingers are directed toward the left, and causing damage at the point of contact. On the left side is another test tube pouring black droplets toward the left onto a black rectangle and causing damage at the point of contact. Both images include four vertical wavy lines that radiate from the point of contact to symbolize smoke or fumes. The images of the test tubes have a black outline and white background and include the images of a black liquid near their pour points. This pictogram is used to warn about the presence of a corrosive hazard.5Gas cylinderThe image of a long black gas cylinder with a short neck and that is leaning toward the right, almost horizontally. This symbol is used to warn about the presence of a compressed gas hazard.A red square, set on one of its points, outlined on a white background, symbolizing danger. It contains, inside its perimeter, the image of a long black gas cylinder with a short neck and that is leaning toward the right, almost horizontally. This pictogram is used to warn about the presence of a compressed gas hazard.6Skull and crossbonesThe image of a black outline of a skull with a white background and black eyes and nose, over two crossed bones depicted by black outlines on white backgrounds. This symbol is used to warn about the presence of an acute toxicity hazard.A red square, set on one of its points, outlined on a white background, symbolizing danger. It contains, inside its perimeter, the black outline of a skull with a white background and black eyes and nose, over two crossed bones depicted by black outlines on white backgrounds. This pictogram is used to warn about the presence of an acute toxicity hazard.7Exclamation markThe image of a large black exclamation mark. This symbol is used to warn about the presence of a health hazard.A red square, set on one of its points, outlined on a white background, symbolizing danger. It contains, inside its perimeter, the image of a large black exclamation mark. This pictogram is used to warn about the presence of a health hazard.8Health hazardThe image of a black torso and head of a person. In the middle of the torso there is a white spot with six white extensions radiating in all directions from the spot. This symbol is used to warn about the presence of a health hazard.A red square, set on one of its points, outlined on a white background, symbolizing danger. It contains, inside its perimeter, the image of a black torso and head of a person. In the middle of the torso there is a white spot with six white extensions radiating in all directions from the spot. This pictogram is used to warn about the presence of a health hazard.9Biohazardous infectious materialsThe image of a small black ring over which there are three large black crescents attached together by the middle of their closed sides, with a small white circle in the middle. This symbol is used to warn about the presence of an infectious or biological hazard.A circle with a black outline on a white background, symbolizing danger. It contains, inside its perimeter, the image of a small black ring over which there are three large black crescents attached together by the middle of their closed sides, with a small white circle in the middle. This pictogram is used to warn about the presence of an infectious or biological hazard.
SOR/2022-272, s. 60(Subsections 2(3) to (5))
Prescribed ClassificationColumn 1Column 2Column 3ItemChemical Name/DescriptionUN Number or CAS Registry NumberClassification1Ammonium picrate, wetted with not less than 10.0% water, by mass1310Physical Hazards Not Otherwise Classified — Category 12Dinitrophenol, wetted with not less than 15.0% water, by mass1320Physical Hazards Not Otherwise Classified — Category 13Dinitrophenolates, wetted with not less than 15.0% water, by mass1321Physical Hazards Not Otherwise Classified — Category 14Dinitroresorcinol, wetted with not less than 15.0% water, by mass1322Physical Hazards Not Otherwise Classified — Category 15Nitroguanidine or picrite, wetted with not less than 20.0% water, by mass1336Physical Hazards Not Otherwise Classified — Category 16Nitrostarch, wetted with not less than 20.0% water, by mass1337Physical Hazards Not Otherwise Classified — Category 17Trinitrophenol, wetted with not less than 30.0% water, by mass1344Physical Hazards Not Otherwise Classified — Category 18Silver picrate, wetted with not less than 30.0% water, by mass1347Physical Hazards Not Otherwise Classified — Category 19Sodium dinitro-o-cresolate, wetted with not less than 15.0% water, by mass1348Physical Hazards Not Otherwise Classified — Category 110Sodium picramate, wetted with not less than 20.0% water, by mass1349Physical Hazards Not Otherwise Classified — Category 111Trinitrobenzene, wetted with not less than 30.0% water, by mass1354Physical Hazards Not Otherwise Classified — Category 112Trinitrobenzoic acid, wetted with not less than 30.0% water, by mass1355Physical Hazards Not Otherwise Classified — Category 113Trinitrotoluene, wetted with not less than 30.0% water, by mass1356Physical Hazards Not Otherwise Classified — Category 114Urea nitrate, wetted with not less than 20.0% water, by mass1357Physical Hazards Not Otherwise Classified — Category 115Zirconium picramate, wetted with not less than 20.0% water, by mass1517Physical Hazards Not Otherwise Classified — Category 116Barium azide, wetted with not less than 50.0% water, by mass1571Physical Hazards Not Otherwise Classified — Category 117Nitrocellulose with water (not less than 25.0% water, by mass)2555Physical Hazards Not Otherwise Classified — Category 118Nitrocellulose with alcohol (not less than 25.0% alcohol, by mass, and not more than 12.6% nitrogen, by dry mass)2556Physical Hazards Not Otherwise Classified — Category 119Nitrocellulose mixture, with not more than 12.6% nitrogen, by dry mass, with or without plasticizer, with or without pigment2557Physical Hazards Not Otherwise Classified — Category 120Dipicryl sulfide, wetted with not less than 10.0% water, by mass2852Physical Hazards Not Otherwise Classified — Category 121Isosorbide dinitrate mixture with not less than 60.0% lactose, mannose, starch or calcium hydrogen phosphate2907Physical Hazards Not Otherwise Classified — Category 122Nitrocellulose membrane filters, with not more than 12.6% nitrogen, by dry mass3270Physical Hazards Not Otherwise Classified — Category 1235-Tert-butyl-2,4,6-trinitro-m-xylene or Musk xylene2956Physical Hazards Not Otherwise Classified — Category 1242-Bromo-2-nitropropane-1,3-diol3241Physical Hazards Not Otherwise Classified — Category 125Isosorbide-5-mononitrate with less than 30.0% non-volatile, non-flammable phlegmatizer3251Physical Hazards Not Otherwise Classified — Category 126Azodicarbonamide, technically pure or preparations having a SADT higher than 75°C3242Physical Hazards Not Otherwise Classified — Category 127Nitroglycerin mixture, desensitized, solid, n.o.s., with more than 2.0% but not more than 10.0% nitroglycerin, by mass3319Physical Hazards Not Otherwise Classified — Category 128Pentaerythritol tetranitrate mixture, desensitized, solid, n.o.s., with more than 10.0% but not more than 20.0% pentaerythrite tetranitrate (PETN) by mass3344Physical Hazards Not Otherwise Classified — Category 129Chlorine dioxideCAS 10049-04-4Physical Hazards Not Otherwise Classified — Category 130Chloropicrin1580Physical Hazards Not Otherwise Classified — Category 131Nitromethane1261Physical Hazards Not Otherwise Classified — Category 132OzoneCAS 10028-15-6Physical Hazards Not Otherwise Classified — Category 133Perchloric acid solutions > 72.0%CAS 7601-90-3Physical Hazards Not Otherwise Classified — Category 134Self-heating liquid, organic, n.o.s.3183Self-heating Substances and Mixtures — Category 135Self-heating liquid, toxic, organic, n.o.s.3184Self-heating Substances and Mixtures — Category 136Self-heating liquid, corrosive, organic, n.o.s.3185Self-heating Substances and Mixtures — Category 137Self-heating liquid, inorganic, n.o.s.3186Self-heating Substances and Mixtures — Category 138Self-heating liquid, toxic, inorganic, n.o.s.3187Self-heating Substances and Mixtures — Category 139Self-heating liquid, corrosive, inorganic, n.o.s.3188Self-heating Substances and Mixtures — Category 1
(Subsection 1(1), subparagraph 3(1)(d)(i), subsection 3(3) and Schedule 1)Information Elements for Specified Categories
PART 1
Combustible DustsColumn 1Column 2Column 3Column 4Column 5ItemCategoryName of SymbolSymbolSignal WordHazard Statement1Combustible Dusts — Category 1No symbolNo symbolWarningMay form combustible dust concentrations in air; orMay form explosible dust-air mixture.
PART 2
Simple AsphyxiantsColumn 1Column 2Column 3Column 4Column 5ItemCategoryName of SymbolSymbolSignal WordHazard Statement1Simple Asphyxiants — Category 1No symbolNo symbolWarningMay displace oxygen and cause rapid suffocation
[Repealed, SOR/2022-272, s. 63]
PART 4
Physical Hazards Not Otherwise ClassifiedColumn 1Column 2Column 3Column 4Column 5ItemCategoryName of SymbolSymbolSignal WordHazard Statement1Physical Hazards Not Otherwise Classified — Category 1(Name of any symbol in Schedule 3 that is applicable to the hazard)(Any symbol in Schedule 3 that is applicable to the hazard)Danger(Wording that describes the nature of the hazard)
PART 5
Biohazardous Infectious MaterialsColumn 1Column 2Column 3Column 4Column 5ItemCategoryName of SymbolSymbolSignal WordHazard Statement1Biohazardous Infectious Materials — Category 1Biohazardous infectious materialsThe image of a small black ring over which there are three large black crescents attached together by the middle of their closed sides, with a small white circle in the middle. This symbol is used to warn about the presence of an infectious or biological hazard.Danger(Wording that describes the nature of the hazard)
PART 6
Health Hazards Not Otherwise ClassifiedColumn 1Column 2Column 3Column 4Column 5ItemCategoryName of SymbolSymbolSignal WordHazard Statement1Health Hazards Not Otherwise Classified — Category 1(Name of any symbol in Schedule 3 that is applicable to the hazard)(Any symbol in Schedule 3 that is applicable to the hazard)Danger(Wording that describes the nature of the hazard)
SOR/2022-272, s. 61SOR/2022-272, s. 62SOR/2022-272, s. 63RELATED PROVISIONS
— SOR/2022-272, s. 64In this section, former Regulations means the Hazardous Products Regulations as they read immediately before the day on which these Regulations come into force.A supplier maysell or import a hazardous product in accordance with the former Regulations; andclassify a product, mixture, material or substance in accordance with the former Regulations if they do so using a category or subcategory of a hazard class listed in Schedule 2 to the Hazardous Products Act as it read immediately before that day on which these Regulations come into force.This section ceases to have effect on the day that is the third anniversary of the day on which these Regulations come into force.SOR/2022-2722022-12-15SOR/2020-382020-03-18