His Excellency the Governor General in Council, on the recommendation of the Minister of Health, pursuant to section 37 of the Canada Consumer Product Safety Acta, makes the annexed Matches Regulations.S.C. 2010, c. 21InterpretationDefinitionsThe following definitions apply in these Regulations.ignition compound means the chemical compound used to cover the end of the splint of the match and to make the match head. (corps inflammable)lot means a stock, batch, shipment or delivery lot of matches. (lot)striking surface means that part of a book, box or other container of matches that is for the purpose of igniting matches. (frottoir)wood matches do not include wood matches that are attached to a common base. (allumette en bois)SpecificationsMatchesMatches must meet the following requirements:the match must not contain any white phosphorus;the ignition compound must be uniformly applied; andthe match head must not be chipped, cracked or crumbling and must not adhere to the head of another match.Additional requirement — wood matchesThe splint of a wood match must be made of good grade and long-fibre wood and must not be broken, split or crushed.MatchbooksA matchbook must meet the following requirements:its cover must, when closed, cover all the match heads;any fastening wire used to secure its cover to the common base of the matches must not pierce or loosen the striking surface;any friction paint on the inside of the cover must not be present within 2.54 cm of the match heads; andits striking surface must be on the side that is opposite to the side that opens.Spontaneous ignitionMatches must not ignite spontaneously when tested in accordance with Schedule 1.Non-disintegration of ignition compoundThe ignition compound must not, when ignited, crack, explode or drop as glowing particles from the match.AfterglowThe splint of a match must not glow for more than three seconds after the flame has been extinguished.Breaking resistance of splintsWhen tested in accordance with Schedule 2, the splint of a match must withstand the following moments without breaking:in the case of a wood match, 700 gf∙cm;in the case of a round match other than a wood match, 100 gf∙cm; andin any other case,300 gf∙cm, when the match is placed on its edge, and100 gf∙cm, when the match is placed flat.InformationName and mailing addressEvery matchbook, box or other container that immediately covers or encloses the matches must carry on it the name and mailing address of the following, in a clear and legible manner:the manufacturer, if the matches are manufactured in Canada; orthe importer or distributor, if the matches are imported.ComplianceMatchesIn order to determine whether a lot of matches complies with the requirements of paragraphs 2(1)(b) and (c), subsection 2(2) and sections 5 to 7, the following procedures are to be used:select at random, based on the number of matches in a lot set out in Column 1 of Table 1 of Schedule 3, a sample that consists of the number of matches set out in Column 2;if a match fails to meet any requirement set out in sections 5 to 7, determine that the match has a major defect;if a match fails to meet a requirement set out in paragraphs 2(1)(b) or (c) or subsection 2(2), determine that the match has a minor defect; andif the number of matches having a major defect is equal to or greater than the number of matches set out in Column 3 of the same table, or if the number of matches having a minor defect is equal to or greater than the number of matches set out in Column 4 of that table, determine that the lot does not comply with the requirements set out in paragraph 2(1)(b) or (c), subsection 2(2) or any of sections 5 to 7, as the case may be.MatchbooksIn order to determine whether a lot of matchbooks complies with the requirements of paragraphs 3(a) to (c), the following procedures are to be used:select at random, based on the number of matchbooks in a lot set out in Column 1 of Table 2 of Schedule 3, a sample that consists of the number of matchbooks set out in Column 2;if a matchbook fails to meet any requirement in paragraphs 3(a) to (c), determine that the matchbook has a defect; andif the number of matchbooks having a defect is equal to or greater than the number of matchbooks set out in Column 3 of the same table, determine that the lot does not comply with one or more of the requirements set out in paragraphs 3(a) to (c).Repeal[Repeal]Coming into ForceRegistrationThese Regulations come into force on the day on which they are registered.(Section 4)Spontaneous Ignition TestThe following method is to be used for testing the spontaneous ignition of matches:place, on a flat surface, a wooden block that is 22 mm thick and 50 mm2 that has a hole that is 25 mm in diameter;fill the hole in the block with the matches to be tested, so that the base of each match is resting on the flat surface, with the match heads pointing up;place the block in the centre of a convection oven at a temperature of 90 ± 1°C;place a temperature sensing device having a range of 65 to 120°C at a minimum distance of 6.5 mm and a maximum distance of 12 mm from, and at the same level as, the match heads; andleave the matches in the oven for a minimum period of two hours.(Section 7)Test for Breaking Resistance of SplintsThe following method is to be used for testing the breaking resistance of splints:insert the match in the holding clamp of the apparatus as illustrated in the figure, while ensuring that the moment arm is2 cm in length, in the case of wood matches; or1.5 cm in length, in the case of matches other than wood matches;gradually lower the holding clamp until the match breaks; andrecord the maximum force registered on the scale required to break the splint.Illustration depicting specifications of the apparatus used to test for the breaking resistance of splints. The screw and pinion arrangement for lowering the holding clamp is shown. The moment arm where the matches are tested is perpendicular to the knife edge.
Figure
(Sections 9 and 10)
TABLE 1
Column 1Column 2Column 3Column 4ItemNumber of matches in a lotNumber of matches in a sampleNumber of matches having a major defectNumber of matches having a minor defect150 or less811251 to 901311391 to 15020114151 to 28032125281 to 50050126501 to 1,200801371,201 to 3,2001252483,201 to 10,00020026910,001 to 35,000315381035,001 to 150,00050041111150,001 to 500,00080061512500,001 and over1,250822
TABLE 2
Column 1Column 2Column 3ItemNumber of books of matches in a lotNumber of books of matches in a sampleNumber of books of matches having a defect150 or less81251 to 90131391 to 1502014151 to 2803215281 to 5005016501 to 1,20080171,201 to 3,200125283,201 to 10,0002002910,001 to 35,00031531035,001 to 150,000500411150,001 to 500,000800612500,001 and over1,2508