Government of Canada / Gouvernement du Canada
Symbol of the Government of Canada

Search

Marine Machinery Regulations

Version of the schedule from 2006-03-22 to 2015-06-16:


SCHEDULE IXNon-Structural Tanks, Short Flexible Hoses and Rigid Plastic and Fibre-Reinforced Plastic Piping and Components

PART I(Section 4)Design Specifications

DIVISION IApplication

ItemApplication
1This Schedule applies to non-structural tanks having a capacity of 4 500 L or less.
2Non-structural tanks having a capacity of more than 4 500 L shall be designed, constructed and installed in accordance with the Hull Construction Regulations.

DIVISION iiSpecifications

ItemRequirements
Non-Structural Tanks of 4 500 L or Less Capacity
1Non-structural tanks shall
  • (a) be made of steel or other material suitable for the liquid contents, the intended use and location of the tanks in the ship;

  • (b) where carbon steel shell plate is used, be of the following minimum plate thickness:

    • (i) 2 mm for capacity not exceeding 100 L,

    • (ii) 3 mm for capacity not exceeding 1 300 L, and

    • (iii) 5 mm for capacity not exceeding 4 500 L;

  • (c) be fitted with stiffeners so that any unsupported flat surface area does not exceed

    • (i) 0.28 m2 where plate thickness does not exceed 3 mm, and

    • (ii) 0.56 m2 where plate thickness does not exceed 5 mm;

  • (d) be fitted with a suitable clean-out door, where capacity exceeds 1 300 L; and

  • (e) have welded or brazed seams, except that where the capacity is not more than 100 L, a solder having a melting point of not less than 425°C may be used.

2Unsupported flat surface areas for different thickness plates of non-structural tanks shall be determined by interpolation or extrapolation.
3Depending on the size and configuration of a non-structural tank, the tank may be required to be fitted with baffles.
Short Flexible Hoses
4Short flexible hoses shall be used where expansion and vibration may be encountered.
5Short flexible hoses shall not be used in the correction of misalignment, except for connection of boiler fuel burners and other removable components.
6Guards shall be fitted on large diameter pipes to reduce the flow of fluid leakage to within the capacity of the space bilge pumps.
7Guards shall be fitted to prevent contact of leaking fluid with surfaces where a hazard may result.
8Short flexible hoses shall be adequate for intended use.
Rigid Plastic and Fibre Reinforced Plastic Piping and Components
9Except in accommodation spaces, service spaces and control locations, piping and components of rigid plastic or fibre reinforced plastic may be used in
  • (a) domestic and sanitary

    • (i) salt water piping systems,

    • (ii) fresh water piping systems, and

    • (iii) waste water piping systems;

  • (b) scupper systems draining inboard but not led within the boundaries of refrigerated chambers;

  • (c) ballast water and fresh water piping systems situated inside tanks used exclusively for ballast water or fresh water;

  • (d) sounding and vent pipes to tanks used exclusively for ballast water or fresh water in non-passenger ships except for sections above the weather deck;

  • (e) sounding pipes to cargo holds in non-passenger ships; and

  • (f) bilge suction pipes in ships not over 24 m in length.

10Piping and components of rigid plastic or reinforced plastic shall not be used
  • (a) in fire extinguishing piping systems;

  • (b) in flammable fluid piping systems;

  • (c) in boiler feed and condensate piping systems;

  • (d) in bilge and ballast piping systems in machinery spaces except as provided for in subitem 9 (f);

  • (e) outboard of sea inlet or overboard discharge valves; and

  • (f) in other piping systems where the use could compromise the safety of the ship or personnel.

11Piping and components of rigid plastic or reinforced plastic shall be protected from
  • (a) vibration;

  • (b) chafing where secured in hangers; and

  • (c) crushing due to overtightening of hanger clamps where they shall be protected by fitting nut-locking or other suitable devices.

12Allowance shall be made for expansion in piping systems.
13Sea inlet and overboard discharge valves shall be of suitable metal construction where connected to plastic or fibre reinforced plastic piping and the piping shall not be installed outboard of the valves.
14When passing through a steel water-tight or fire control bulkhead, a steel spool-piece shall be attached to the bulkhead or deck and, at a water-tight bulkhead or deck a metallic shut-off valve shall be installed immediately adjacent to the spool-piece except that no valve is required on ballast or fresh water piping located within ballast or fresh water tanks.
15Remote controls operable from above the bulkhead deck shall be fitted to the shut-off valve except where
  • (a) the piping on one side of the bulkhead or deck is completely metallic and the valve is fitted to the metallic piping and easily accessible; or

  • (b) two readily accessible valves are installed, one on either side of the bulkhead or deck.

16When passing through a bulkhead or deck material other than steel, the installation shall be such that the fire, watertight and structural integrity of the bulkhead or deck is not diminished due to penetration.

PART II(Section 6)Plans

ItemRequired Information
Non-Structural Tanks of 4 500 L or Less Capacity
1General arrangement of the tank installation and the system to which it is connected.
2Details of
  • (a) nature of the fluid to be contained in the tank;

  • (b) tank volume and design fluid head;

  • (c) tank materials, sizes, plate seams and supports; and

  • (d) tank openings, vents and other connections.

3Detailed strength calculations where
  • (a) tank design pressure head exceeds 5 m; or

  • (b) tank material is other than steel.

Short Flexible Hoses
4Material specifications including details of construction and end connection arrangements.
5Details of the various tests applied to the hoses and identification of the standards association whose testing standards were applied.
6Details of the design working pressures, temperatures, fluid flow velocities and nature of the fluids to be carried.
Rigid Plastic and Fibre-Reinforced Plastic Piping and Components
7Material specifications, physical properties, details of the various tests carried out and identification of the standards association whose testing standards were applied.
8Characteristics of flammability, decomposition resistance to environmental conditions and abrasion resistance to sand, ice particles or other fluid entrained substances.
9Details of connections, scantlings, design working pressures, temperatures and fluid flow velocities.
10Details of piping systems, locations, supports and thermal expansion allowances taking into account differences in the thermal expansion properties of plastic materials and metal.

PART III(Subsection 12(2))Construction and Installation Inspections

ItemRequirements
1Construction and installation inspections shall consist of completion of each item set out in Part III of Schedules X to XV for the relevant fluid system.

PART IVPeriodic General Inspections and Periodic Special Inspections

DIVISION I(Section 19)Periodic General Inspection

ItemRequirements
1Completion of each item set out in Division I of Part IV of Schedules X to XV for the relevant fluid system.

DIVISION IIPeriodic Special Inspection

SUBDIVISION I(Subsection 20(1))Parts to be Inspected
ItemRequirements
1No periodic special inspection is required if a general examination shows that the condition of the tanks is suitable for further service.
SUBDIVISION II(Subsection 20(2))Intervals
ItemRequirements
1None.

Date modified: